Optional Accessories - Makita DF333D Manual De Instrucciones

Screwdriving operation
CAUTION:
Adjust the adjusting ring to the
proper torque level for your work.
CAUTION:
Make sure that the driver bit is
inserted straight in the screw head, or the screw
and/or driver bit may be damaged.
Place the point of the driver bit in the screw head and apply pres-
sure to the tool. Start the tool slowly and then increase the speed
gradually. Release the switch trigger as soon as the clutch cuts in.
NOTE: When driving wood screw, pre-drill a pilot hole
2/3 the diameter of the screw. It makes driving easier
and prevents splitting of the workpiece.
Drilling operation
First, turn the adjusting ring so that the arrow points to
the marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the drill bit into the workpiece.
Drilling in metal
To prevent the drill bit from slipping when starting a hole, make an
indentation with a center-punch and hammer at the point to be drilled.
Place the point of the drill bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
CAUTION:
Pressing excessively on the tool will
not speed up the drilling. In fact, this excessive pressure
will only serve to damage the tip of your drill bit, decrease
the tool performance and shorten the service life of the tool.
CAUTION:
Hold the tool firmly and exert care
when the drill bit begins to break through the
workpiece. There is a tremendous force exerted on
the tool/drill bit at the time of hole break through.
CAUTION:
A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it firmly.
CAUTION:
Always secure workpieces in a
vise or similar hold-down device.
CAUTION:
If the tool is operated continuously until
the battery cartridge has discharged, allow the tool to rest
for 15 minutes before proceeding with a fresh battery.
Using the tool as a hand screwdriver
► Fig.14
Switch off the tool.
Move the reversing switch lever to the neutral position.
Turn the adjusting ring so that the arrow points to the
Turn the tool.
NOTE: This use is convenient for checking the screwdriving.
NOTE: Do not use the tool for work requiring excessive
force, such as tightening bolt or removing rusted screws.
Using holster
Optional accessory
CAUTION:
driver bit/drill bit from the tool.
CAUTION:
comes to a complete stop before placing it in the
holster.
Be sure to close the holster securely with the
holster button so that it holds the tool firmly.
1. Thread a waist belt or similar through holster holder.
► Fig.15: 1. Holster holder 2. Waist belt
2. Put the tool in the holster and lock it with the holster button.
► Fig.16
► Fig.17
You can keep two driver bits at the front of the holster.
MAINTENANCE
CAUTION:
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Drill bits
• Driver bits
• Socket bits
• Driver bit holder
• Holster
• Plastic carrying case
marking.
• Hook
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
10 ENGLISH
When using the holster, remove a
Turn off the tool and wait until it
Always be sure that the tool is
Never use gasoline, benzine, thinner,
These accessories or attachments