ENGLISH
Original instructions
TABLE OF CONTENTS
Safety Warnings ........................................................................................23
Sander Safety Rules ..................................................................................23
Specifications............................................................................................23
Contents of Package .................................................................................24
Assembly/Adjustments .............................................................................24
Operation...................................................................................................24
Trouble Shooting ......................................................................................25
Wiring Diagram ........................................................................................57
Parts...........................................................................................................57
Parts Explosion .........................................................................................58
FOR YOUR SAFETY:
READ ALL INSTRUCTIONS CAREFULLY
Operatyr Safety: Required Reading
IMPORTANT! Safety is the single most important consideration in the
operation of this equipment. The following instructions must be followed
at all times.
There are certain applications for which this tool was designed. We strong-
ly recommend that this tool not be modified and/or used for any other appli-
cation other than that for which it was designed. If you have any questions
about its application, do not use the tool until you have contacted us and we
have advised you.
General Safety Warnings
KNOW YOUR POWER TOOL. Read the owner's manual carefully.
Learn the tool's applications, work capabilities, and its specific potential
hazards.
ALWAYS GROUND ALL TOOLS.
If your tool is equipped with a three-pronged plug, you must plug it
into a three-hole electric receptacle. If you use an adapter to accom-
modate a two-pronged receptacle, you must attach the adapter plug to
a known ground. Never remove the third prong of the plug. ALWAYS
AVOID DANGEROUS ENVIRONMENTS. Never use power tools in
damp or wet locations. Keep your work area well lighted and clear of clutter.
ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES
FROM TOOLS AFTER USE.
Form the habit of checking to see that keys and adjusting wrenches
are removed from the tool before turning it on. ALWAYS KEEP
YOUR WORK AREA CLEAN. Cluttered areas and benches invi-
te accidents.
ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.
All visitors should be kept a safe distance from the work area.
ALWAYS MAKE THE WORKSHOP CHILDPROOF. Child-
proof with padlocks, master switches, or by removing starter keys.
NEVER OPERATE A TOOL WHILE UNDER THE INFLU-
ENCE OF DRUGS, MEDICATION, OR ALCOHOL.
ALWAYS WEAR PROPER APPAREL.
Never wear loose clothing or jewelry that might get caught in
moving parts. Rubber-soled footwear is recommended for the best
footing.
ALWAYS USE SAFETY GLASSES AND WEAR HEARING PRO-
TECTION.
Also use a face or dust mask if the cutting operation is dusty.
NEVER OVERREACH.
Keep your proper footing and balance at all times.
NEVER STAND ON TOOLS.
Serious injury could occur if the tool is tipped or if the cutting tool
is accidentally contacted.
ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories
such as blades, bits, and cutters. ALWAYS AVOID ACCIDEN-
TAL STARTING. Make sure switch is in "OFF" position before
plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED.
ALWAYS CHECK FOR DAMAGED PARTS.
Before initial or continual use of the tool, a guard or other part that
is damaged should be checked to assure that it will operate proper-
ly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other dama-
ged parts should immediately be properly repaired or replaced.
Special Safety Rules For Disc Sanders
SAVE THESE INSTRUCTIONS.
Refer to them often.
1.Do not operate this machine until you have read all of the following
instructions.
2.Do not attempt to operate this machine until it is completely assembled.
3.Do not turn ON this machine if any pieces are missing.
4.If you are not familiar with the operation of the machine, obtain assis-
tance from a qualified person.
5.It is highly recommended that this machine be firmly mounted to a flat
and secure work surface or stand.
6. Always wear protective eyewear prior to operating this machine.
7.Do not operate this machine if you are under the influence of drugs
and/or alcohol.
8. Remove all jewelry prior to operating this machine.
9. Do not wear any gloves while operating this machine.
10. Always make sure the power switch is in the OFF position prior to plug-
ging in the machine.
11. Always make sure the power switch is in the OFF position when doing
any assembly or setup operation.
12. Always wear a dust mask and use adequate dust collection and proper
ventilation. Use of sanders can produce harmful particles while sanding
certain types of woods.
13. The use of any accessories or attachments not recommended may cause
injury to you and damage your machine.
14. This machine must be properly grounded.
15. Abrasive discs should be the recommended diameter of the manufactu-
rer.
16. Always keep your face and hands clear of moving parts such as belts
and pulleys.
17. Keep power supply cords free of moving parts of the sander. Damaged
cords can result in electric shock.
18. Maintain a 1/16" clearance between the sanding disc and table.
19. Always support the workpiece with the table.
20. Remove material or debris from the work area. Keep work area neat and
clean.
21. Keep these instructions for future reference.
Specifications
Art. No. ................................................................
Luna .....................................................................
Disc Diameter ................................................mm
Table Tilt ..............................................................
Positive Stops.......................................................
Table Size ......................................................mm
Disc Speed.....................................................rmp
Disc Brake ...........................................................
Motor ..............................................................HP
Volts ..................................................................V
Net Weight .......................................................kg
23
20009-0108
BDS 300
305
45° Down
0°, 22,5°, 45°
435 x 165
1420
Manual
1
230
33
87 dB87 dB