Descargar Imprimir esta página

Publicidad

Enlaces rápidos

Parts/Pièces/Herrajes

Publicidad

loading

Resumen de contenidos para West Elm adams 6 drawer wide chest

  • Página 1 Parts/Pièces/Herrajes...
  • Página 2 Anti tip kit 2x Nylon Strap 2x Mounting Plate 4x Small Screw 4x Large Screw 4x Kit anti chavirement – 2x Kit para evitar que voltee Bretelle en nylon – x2 Cinta de Nylon 2x Plate de montage - x4 Placa de montaje 4x Vis petite x4 Vis grande x4 Tornillo Pequeño 4x Tornillo Largo 4x...
  • Página 3 Drawer Construction repeat for all 6 drawers: 1. Lay the opposite drawer sides onto a clean smooth surface such as carpet or cardboard. Align drawer guides with drawer sides as shown. Insert screws (J) and dowels (C). Press in the cam locks (A) as shown. 1.
  • Página 4 3. Attach left and right drawer sides to drawer fronts. Tighten small cam locks (A) with screwdriver. 3. Fixez le panneau latéral gauche et droit à la façade du tiroir. Serrez les petites serrures à came (A) à l’aide du tournevis. 3.
  • Página 5 6. Attach drawer pull (E) using bolt (F). 6. Fixez la poignée au tiroir (E) en util isant les boulons (F). 6.Coloque la manilla (E) utilizando per nos (F) 7. Insert large wooden dowels (H) into the side panels and the partition as shown. Screw on side guides with screws (M) as shown.
  • Página 6 8. Insert 4 large woden dowels (H) into the front rails. 8. Insérez 4 gros goujons en bois (H) dans les traverses avant. 8. Inserte 4 pasadores largos HJ) en los agujeros en los rieles frontales. 9. Lay the top panel onto a clean smooth surface such as carpet or cardboard.
  • Página 7 11. Align partition with bottom panel. Insert bolt (C). Tighten with supplied allen key. 11. Alignez la cloison avec le panneau inférieur. Insérez des boulons (C). Serrez-les à l’aide de la clé hexago nale fournie. 11. En le la partición con el panel inferior. Inserte el perno (C). Apriete con la llave allen suministrada.
  • Página 8 12. Align Side panels to bottom panel and rails as shown. Press rmly together. Insert bolt (C). Tighen with supplied hex key. 12. Alignez les panneaux latéraux au panneau inférieur et aux traverses comme illustrés. Pressez-les ferme ment ensemble. Insérez les boulons (C). Serrez-les à l’aide de la clé hexagonale. 12.
  • Página 9 13. Slide in back panel as shown. Screw in legs as shown. Do not overtighten. 13. Glissez le panneau arrière comme illustré. Vissez les pieds comme illustrés. Ne les serrez pas trop. 13. Deslice el panel trasero como se muestra. Atornille las patas como se muestra. No apriete demasiado.
  • Página 10 14. Insert cam locks (G) into the end panels and partitions as shown. Align top panel and press mly together. Turn cam locks 180 degrees or until locked. 14. Insérez des serrures à came (G) dans les panneaux latéraux et la cloison comme illustré. Alignez le pla teau et pressez-les fermement ensemble.
  • Página 11: Care Instructions

    15. Insert drawers bottom rst. Align with drawer guides on side panels. 15. Enfoncez les tiroirs inférieurs en premier. Alignez-les avec les glissières situées sur les côtés. 15. Inserte los cajones inferiores primero. En le con las guías en los paneles laterales. CARE INSTRUCTIONS Hardware may loosen overtime.
  • Página 12 back side wall NOTICE: To prevent injury and property damage from unexpected tipping of furniture, we highly recommend installa tion of the anti-tip kit included with this product. Attaching furniture to wall with anti-tip kits. 1. Determine where the piece is to be placed and mark location on the wall for the mounting bracket screw holes. They should be placed approximately 1”...
  • Página 13 NOTICE: To prevent injury and property damage from unexpected tipping of furniture, we highly recommend installation of the anti-tip kit included with this product. Attaching furniture to wall with anti-tip kits. 1. Determine where the piece is to be placed and mark location on the wall for the mounting bracket screw holes.