Noise/Vibration Information; Charging The Battery - Bosch EXACT ION 18 V-LI 2-700 Manual Original

16 | English
Industrial cordless screwdriver
EXACT ION
Battery (not included with the
product as standard)
Permitted ambient temperature
– during charging
A)
– during operation and dur-
ing storage
Recommended batteries
– GBA 18 V...
(battery pack L)
(0 602 494 002)
– GBA 18 V...
(battery pack XL)
(0 602 494 004)
Recommended chargers
A) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted sound pressure level of the power
tool is 70 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
2 2
a < 2.5 m/s , K = 1.5 m/s ,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
1 609 92A 4R0 | (18.01.2019)
2-700 4-2000
Li-ion Li-ion
°C 0 to +45 0 to +45
°C -20 to +50 -20 to +50
● ●
− −
AL 18.. AL 18..
GAL 3680 GAL 3680
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.

Charging the Battery

Use only the chargers listed on the accessories page.
u
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery (see figures A1–A2)
The battery (9) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (10) unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery (9), press the release button (10)
and pull the battery forward and out of the power tool. Do
not use force to do this.
6-1500 8-1100 12-450
Li-ion Li-ion
0 to +45 0 to +45 0 to +45
-20 to +50 -20 to +50 -20 to +50
● ●
− −
AL 18.. AL 18.. AL 18..
GAL 3680 GAL 3680 GAL 3680
12-700
Li-ion Li-ion
0 to +45
-20 to +50
● ●
− −
AL 18..
GAL 3680
Bosch Power Tools