Power Supply Installation - Vimar ELVAX M832 Manual Para El Conexionado Y El Uso

FEATURES
Timing (cycles) and load:
Terminals: 12/0: 12V a.c. 0,8A continuous + 1A inter-
mittent 30 sec. ON 150 sec. OFF
P = 35VA supply voltage 230V a.c. (other voltages
upon request) 50-60 Hz
PRI: Protection by PTC

POWER SUPPLY INSTALLATION

The power supply must be installed in a dry place
away from direct heat or dust. Ensure easy access
for inspection and maintenance. Secure the unit to
the wall with the anchor bolts provided or insert it into
a rack with a omega DIN bar. Before connecting the
unit use a tester to make sure that the cables are not
broken or short-circuited. For user safety, the equip-
ment operates at a low voltage and is separated from
the mains by a high-insulation transformer. We rec-
ommend installation of an overload cutout of appropri-
ate capacity between the mains and the unit.
Warning: Cut off mains supply for 3 minutes to
reset the device after an overloading.
Product is according to CE mark and directives:
- EC Directives 2004/108/CE and following norms.
- EC Directives 2006/95/CE (73/23/CEE).
Power supply units constitute SELV sources in com-
pliance with the requirements stipulated in Article
411.1.2.2 of CEI standard 64-8 (ed. 2003).
Production is subject to costant surveillance:
D V E
EN
SAFETY INSTRUCTIONS FOR INSTALLERS
- Carefully read the instructions on this leafl et: they give important
information on the safety, use and maintenance of the installation.
- After removing the packing, check the integrity of the set. Packing
components (plastic bags, expanded polystyrene etc.) are dange-
rous for children. Installation must be carried out according to natio-
nal safety regulations.
- It is convenient to fi t close to the supply voltage source a proper
ominipolar type switch with 3 mm separation (minimum) between
contacts.
- Before connecting the set, ensure that the data on the label corre-
spond to those of the mains.
- Use this set only for the purposes designed, i.e.for electric door-o-
pener systems. Any other use may be dangerous. The manufacturer
is not responsible for damage caused by improper, erroneous or
irrational use.
- Before cleaning or maintenance, disconnect the set.
- In case of failure or faulty operation, disconnect the set and do not
open it.
- For repairs apply only to the technical assistance centre authorized
by the manufacturer.
- Safety may be compromised if these instructions are disregarded.
- Do not obstruct opening of ventilation or heat exit slots and do not
expose the set to dripping or sprinkling of water.
- Installers must ensure that manuals with the above instructions are
left on connected units after installation, for users' information.
- All items must only be used for the purposes designed.
- WARNING: to avoid the possibility of hurting yourself, this unit must
be fi xed to the wall according to the installation instructions.
- This leafl et must always be enclosed with the equipment.
Directive 2002/96/EC (WEEE)
The crossed-out wheelie bin symbol marked on the product
indicates that at the end of its useful life, the product must be
handled separately from household refuse and must therefore
be assigned to a differentiated collection centre for electrical
and electronic equipment or returned to the dealer upon purchase of a
new, equivalent item of equipment.
The user is responsible for assigning the equipment, at the end of its
life, to the appropriate collection facilities.
Suitable differentiated collection, for the purpose of subsequent
recycling of decommissioned equipment and environmentally compa-
tible treatment and disposal, helps prevent potential negative effects on
health and the environment and promotes the recycling of the materials
of which the product is made. For further details regarding the collection
systems available, contact your local waste disposal service or the shop
from which the equipment was purchased.
Risks connected to substances considered as dangerous (WEEE).
According to the WEEE Directive, substances since long usually used
on electric and electronic appliances are considered dangerous for pe-
ople and the environment. The adequate differentiated collection for
the subsequent dispatch of the appliance for the recycling, treatment
and dismantling (compatible with the environment) help to avoid pos-
sible negative effects on the environment and health and promote the
recycling of material with which the product is compound.
3