Publicidad
Idiomas disponibles
Idiomas disponibles
Installation instructions – LED Recessed Canopy
13. Align the four sheet metal screws that were drilled into
the canopy with the four hole openings in fixture frame
(Figure 4).
14. Take the corrugated cardboard sheet out of the fixture
by peeling the tape off.
15. Attach the tether to the door by unscrewing nut from
the door, placing the tether onto the stud and tighten
the nut back on (Figure 6).
16. Screw the door into the fixture while making sure the
tether does not get caught up in gasket and tighten
four door screws (use two diagonal studs as guide
to locate door screws Figure 6). Ensure screws are
tightened all the way (torque 15 in. lb.).
17 . Clean off glass surface after door installation; avoid
LED contact and use only Vinegar based multi-surface
cleaners (windex multi-surface vinegar or similar).
Retrofit And New Construction Application (Open
Canopy, Top Installation )
N
ote:
Incoming power leads must not exceed 16 gauge.
1.
Make sure power is turned off.
2.
If retrofit, remove old fixture from the canopy ceiling. If
new construction skip to Step 4.
3.
Clean the entire surface on both sides of the canopy
surface around the new opening. Remove any dirt,
debris, old paint and rust scale. Clean approximately 2'
in each direction on top of the canopy; approximately
6" on bottom of canopy.
4.
Remove new fixture from carton and set it on a clean
surface; remove the driver box door by loosening four
Philip head screws. Set the door and screws aside.
N
ote:
Inside of the box has protective packing around the
knockout, leave this intact to protect the driver during
next step.
5.
Flip fixture over and loosen four door screws. Carefully
place the door aside while making sure not to scratch
the glass lens and painted door.
Do not remove the corrugated cardboard sheet from
N
ote:
the opening until after installation.
6.
Beneath the canopy, using the existing opening as
center point, cut out 14 x 14 inch square opening in the
canopy with template provided (Figure 1a).
7 .
Use the template to screw in four sheet metal screws
provided through holes opening. These four screws
through the canopy will help as a guide pins when
installing the fixture from top side of canopy
(Figure 1b).
8.
On top of the canopy, with the incoming wires coming
through 1/2" water tight conduit, insert incoming power
leads into the wire holes in grommet provided; Make
sure to have at least 3" of wires through the grommet;
Push the grommet into the conduit opening.
4
COOPER LIGHTING SOLUTIONS
IB515007EN
Installation instructions
9.
Secure water tight conduit with connector and
incoming power leads into the hole of the driver box
housing. The conduit connector must have a gasket
on outside for sealing. Tighten the connector with
locknut on the inside of the driver box. Make sure the
connector is snug fit against the box opening.
10. Make splice connections inside the box: Connect Black,
White and Ground wire inside the box with matching
wires by lifting the wago connector levers and inserting
wires into the connectors. Once inserted properly,
press lever back into lock position and tug on the wires
to make sure proper connection is made.
For vertical wide reflector only (LRC-VAT), before step
N
ote:
11 properly orient the fixture (Figure 2) As desired;
locate the orientation label and orient the fixture
accordingly. Arrow should point to direction of throw.
11. Tighten the driver box door back with Philip head
screws (torque: 25 in. lbs.) and ensure driver box
gasket stays in place during this step.
12. Apply 1/4" bead of Industrial strength sealant/adhesive
(Not Provided) around the perimeter of the housing
frame plate as shown (Figure 5).
13. Flip the fixture over with housing facing up and use
the four sheet metal screws as guide pins to place the
fixture on top of the canopy Figure 4.
14. Apply hand pressure around the perimeter to ensure
sealant contacts the canopy top.
15. Apply sealant around the four screws to cover up screw
opening around the sheet metal plate and tighten the
four nuts provided.
16. Beneath the canopy, take the corrugated cardboard
sheet out of the fixture by peeling the tape off.
17 . Attach the tether to the door by unscrewing nut from
the door, placing the tether onto the stud and tighten
the nut back on (Figure 6).
18. Screw the door into the fixture while making sure the
tether does not get caught up in gasket and tighten
four door screws (use two diagonal studs as guide
to locate door screws Figure 6). Ensure screws are
tightened all the way (torque: 15 in. lbs.).
19. Clean off glass surface after door installation; avoid
LED contact and use only vinegar based multi-surface
cleaners (Windex multi-surface vinegar or similar).
Maintenance:
N
ote:
A regular maintenance schedule should be
followed to retain optimal light output and thermal
performance.
Optical reflector cleaning should be performed with a
clean dry cloth to remove any dust or other contaminants.
Additional cleaning can be performed with a cloth
dampened with vinegar based multi-surface cleaners
(Windex multi-surface vinegar or similar). Avoid spraying on
LEDs.
Publicidad
