Bosch GGS Professional 6 Manual Del Usuario página 22

OBJ_BUCH-1050-002.book Page 22 Tuesday, November 2, 2010 3:50 PM
22 | English
Protection Guard for Grinding (GGS 6)
(see figure E)
Place the protection guard 11 on the spindle
collar. Adapt the position of the protection
guard 11 to the requirements of the work step.
Lock the protection guard 11 with the two lock-
ing nuts 19 and tighten the locking nuts with at
least 10 Nm.
After mounting the grinding tool, shut the pro-
tection guard 11 and tighten both wing nuts.
Mounting the Grinding Tools
The grinding tools must run completely concen-
trically. Do not continue to use damaged grind-
ing tools that are out of balance. If the grinding
tools are out of balance they should be re-
placed. Treat with a whetstone (accessory) or
change.
Using a whetstone, any particular special shape
can be produced out of the basic forms of the
grinding accessory.
When using grinding tools with a threaded in-
sert, pay attention that the end of the grinder
spindle 3 does not touch the hole base of the
grinding tool.
GGS 6 S (see figure B)
– Turn the grinder spindle 3 until the hole in
the grinder spindle 3 and the openings of the
housing are aligned. Insert the holding rod 15
through the hole of the grinder spindle 3.
– Loosen and remove the clamping nut 1 with
the two-pin spanner 16 provided.
– Clean the grinder spindle 3 and all parts to
be mounted.
– Mount the grinding accessory and tighten
clamping nut 1 with two-pin spanner 16. Pay
attention that the grinding accessory can ro-
tate freely in protection guard 2.
Use tapered grinding accessories only in
conjunction with the open protection guard
2 and the matching clamping system
(clamping nut 1 and mounting flange 4).
1 609 929 S82 | (2.11.10)
GGS 6 (see figure F)
– Turn the grinder spindle 3 until the hole in
the grinder spindle 3 and the openings of the
housing are aligned. Insert the holding rod 15
through the hole of the grinder spindle 3.
– Loosen the clamping nut 9 with the open-end
spanner 20 (size 24 mm) by turning in anti-
clockwise direction.
– Remove the clamping flange 10.
– Clean the grinder spindle 3 and all parts to
be mounted.
– Mount the grinding accessory and clamping
flange 10 and tighten clamping nut 9 with
open-end spanner 20 (size 24 mm). Pay at-
tention that the grinding accessory can ro-
tate freely in protection guard 11.
Use straight grinding accessories only in
conjunction with the enclosed protection
guard 11 and the matching clamping system
(clamping nut 9, clamping flange 10 and
mounting flange 12).
Changing the Mounting Flange
(see figure D)
GGS 6 S
To fasten tapered grinding accessories, use
mounting flange 4, clamping nut 1 and the open
protection guard 2.
Lever snap ring 18 out of the groove in grinder
spindle 3 using a screwdriver and remove
mounting flange 4. Mount the fitting mounting
flange 4 analogously.
GGS 6
To fasten straight grinding accessories, use
mounting flange 12, clamping nut 9, clamping
flange 10 and the enclosed protection guard 11.
Lever snap ring 18 out of the groove in grinder
spindle 3 using a screwdriver and remove
mounting flange 12. Mount the fitting mounting
flange 12 analogously.
Bosch Power Tools