Publicidad
Idiomas disponibles
Idiomas disponibles
Electrical connection
• The electrical safety of this appliance can only be guar-
anteed if the latter is correctly and efficiently earthed,
in compliance with regulations on electrical safety. Al-
ways ensure that this vital safety measure has been
taken. If you have any doubts, call in a qualified techni-
cian to check the electrical system thoroughly.
• The manufacturer denies all responsibility for damage
resulting from a system which has not been earthed
correctly.
• Before powering the appliance, check whether the tech-
nical characteristics featured on the appliance data plate
correspond with those of the mains electrical system.
• Check that the current load of the mains supply and of
the power sockets is suitable for the maximum power
of the appliance, indicated on the appliance data plate.
If in doubt, contact a qualified professional.
Disconnect the appliance from the electricity supply
before all operations.
Connect your hob to the electrical system by means of a
junction box: if the appliance is connected permanently
to the mains, an omnipolar circuit breaker, accessible
if necessary, with a minimum contact opening of 3 mm
should be installed.
Valid only for models with a power supply cable
Some models are supplied with a single-phase power sup-
ply cable, and should consequently only be connected to
the single-phase mains. Observe the wire colours, as indi-
cated in the diagram attached.
Electrical connections
Voltage, Frequency
FR-BE-AT-DE-GR-ES-IL-
IT-NZ-PT-GP-CH-MA-LU-
IE-FI-SE-IS-GB-NL-DK
230V - 1+N~ 50Hz
CY-MT-AU-NZ-KW
240V - 1+N~ 50Hz
FR-BE-NO
230V - 2 ~ 50Hz
BR=BRUN,BL=BLEU
BR=BRAUN, BL=BLAU
BR=BRUIN, BL=BLAUW
BR=BROWN, BL=BLUE
* Application of the simultaneity coefficient in accordance with
cei 60335-2-6 norm
Valid only for models without a power supply cable
Some models are not fitted with a power supply cable, as
the cable should be sized according to the type of electrical
connection in use (see connection table below). To connect
the cable, proceed as follows:
•
Using a screwdriver, prise on the side tabs of the terminal
board cover;
•
Pull open the cover of the terminal board.
Technical characteristics
To install the cable, proceed as follows:
•
•
•
•
Fuses, Sections
25A *
2,5 mm²
This appliance conforms with the following European
Community Directives:
-
-
-
Warning: If the hob is fitted above a built-in oven, the hob
and the oven must be connected to the mains separately
for safety reasons and to simplify operations when it is
necessary to pull the oven out for some reason.
28
unscrew the wire clamp screw and the contact screws.
to make the desired electrical connection (see table),
use the jumpers housed inside the box. Position the
power supply cable wires according to the indications
in the table.
once the connections have been made, tighten all the
terminal screws fully.
Fasten the supply cable in place with the clamp and
close the cover of the terminal board.
Electrical connections
1
2
3
4
5
L
N
1
2
3
4
5
L1
L2
1
2
3
4
5
L1
L2
N
1
2
3
4
5
L1
L2
L3
1
2
3
4
5
L1
L2
L3
N
1
2
3
4
5
L1
L2
N1
N2
1
2
3
4
5
L
N
* Application of the simultaneity coefficient in accordance with
cei 60335-2-6 norm
73/23/EEC of 19/02/73 (Low Voltage) and subsequent
amendments;
89/336/EEC of 03/05/89 (Electromagnetic compatibility)
and subsequent amendments;
93/68/EEC of 22/07/93 and subsequent amendments;
Voltage,
Fuses,
Frequency
Sections
FR-AT-BE-DE-GP--
ES-IE-IL-IS-IT-LU-
25 A*
RE-FI-GB-GR-PT--
2,5 mm²
SE-MA-NZ
230V-1+N~50 Hz
FR-BE-NO
25 A*
2,5 mm²
230V-2~50/60 Hz
FR-BE-CH-DE-AT--
ES-IL-IT-NZ-PT-
16 A*
MA- LU-SE-IS-NL
1,5 mm²
400V2-N~50 Hz
FR-BE-NO
16 A*
1,5 mm²
230V3~50 Hz
FR-AT-BE-DE-ES-
IL-IS-IT-LU-PT-SE
16 A*
-MA-NZ-CH-DK-N-
1,5 mm²
L
400V3+N~50 Hz
NL
16 A*
1,5 mm²
230V2+2-N~50 Hz
CY-AU-NZ-KW-MT
25 A*
2,5 mm²
240V-1+N~50 Hz
Publicidad
