Fricosmos 054244 Manual Del Usuario página 4

Read the instructions before connecting the device and store them in a safe place for
reference.
DO NOT DRINK WATER FROM THE HAND WASHBASIN. THIS DEVI-
CE IS NOT DESIGNED FOR DRINKING WATER.
This hand washbasin cannot replace any items that require hot and cold
running water at the facilities in accordance with the applicable laws
CONTENTS & AVAILABLE SPARES
Cabinet with sink. (spare part not available)
463204 - Double inlet angled tap
454202 - Drain valve with overfl ow
454260 - Flexible drain
461426 - Plastic tank 20 l.
Other spare parts:
461432 - "Not drinking water" vinyl adhesive for tank.
485002 - Swivel wheel with brake in galvanized steel and rubber ø75 mm.
485004 - Swivel wheel without brake in galvanized steel-rubber ø75 mm
085006 - Kit for fi xing castor to tube 40x40
MOUNTING
Check the content.
It is advisable to use cut resistant gloves for assembly operations.
Connect the tap by inserting it through the upper hole of the cabinet and fi x it with the supplied nut
Connect the cold water hose from the tap to the outlet of the mixing tee.
Connect the hot water hose from the tap to the outlet of the heater.
Mount the drain valve · Fig. 1
Insert the tank with a non-drinking water label under the sink bowl.
Connect the fl exible drain to the valve shaping it as a syphon and insert the other end into the tank·
Fig. 2
Place the unlabeled tank under the drainer and insert the pump hose inside.
Remove the protective plastics from the doors and the furniture.
The heater must be connected by an authorized electrician.
The heater must be connected according to its manual.
COMISSIONING
Make sure the heater is unplugged. If the heater runs empty, it can cause malfunctions that are not
covered by the warranty.
Connect the pump to electrical power.
Turn on cold water from the tap until airless water comes out.
Turn on the hot water from the tap until airless water comes out.
Connect the heater to the network.
USE
Before plugging in the heater make sure it is full of water. If the heater runs empty, it can cause
malfunctions that are not covered by the warranty. Check the point "Commissioning"
To turn on the faucet and increase the fl ow, lift the lever upwards.
To turn off the water, lower the tap lever.
To regulate the water temperature, move the lever sideways.
SAFETY, CLEANING AND STERILIZATION
The equipment must only be repaired by the manufacturer or an authorized electrician.
Before any cleaning operation, unplug the device from the mains.
Do not drink water from the sink.
This sink cannot replace any other item that requires hot and cold running water according to cu-
rrent applicable regulation.
CLEANING AND STERILIZATION
• Wear protective glasses, gloves and masks when fi lling, emptying and cleaning the drums.
• Wash both drums with plenty of potable water.
• Sterilize them before the fi rst use of every day by adding a sterilizing product approved for
drinking water following the manufacturer's instructions. Drive all the water with sterilant from
the clean water drum through the circuit by opening the cold water tap until the drum is completely
emptied to sterilize the circuit.
• Then fi ll the clean water tank with drinking water.
• It is now ready for use.
• Perform this procedure before starting every working day.
SECURITY
• Empty the used water tank at least once an hour or when it is full.
• Empty the clean water tank at least once every 6 hours.
• When you do not use the equipment for a long period of time, empty the water tanks, wash them
and store them completely dry. Store clean, dry drums in a dark, dry and healthy place.
• Replace the tanks every two months.
STAINLESS STEEL MAINTENANCE
• Use only water and neutral soap when cleaning.
• Wipe with a soft cloth.
• Rinse with plenty of drinking water.
• Dry with a soft cloth.
• Do not use acids or strong detergents and do not rub with a scourer or spatula.