Philips LivingColors Generation 3 Manual De Instrucciones página 6

Problem
LivingColors is not providing light
LivingColors does not respond to
the remote control
I cannot link multiple LivingColors
lamps
I cannot start the automatic color
changing mode
LivingColors is still not working to
the correct standards
Plug specification:
AC adapter
Input: 100 - 240 V ~ 50/60 Hz
Output: 24 V 0.5A
Power consumption of the luminaire: up to 10W
Remote Control:
Batteries: 2 x Philips Powerlife Alkaline AAA LR03, 1.5 V.
Wireless specification:
Wireless RF mode frequency band:
Wireless communications protocol:
Operating channels:
Environmental specification:
Temperature (operation):
Temperature (Storage):
Relative humidity:
Disposal of your old product
Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused. Please inform
yourself about the local separate collection system for electrical and
electronic products. Please act according to your local rules and do not
dispose of your old products with your normal household waste. The
correct disposal of your old product will help prevent potential negative
consequences for the environment and human health.
Warranty:
Philips' two-year warranty is valid if the product is used in accordance
with the instructions and for its intended purpose. Claims will only be
accepted on submission of the original proof of purchase (invoice, sales
440401838521.indd 3
Possible cause
The lamp is not plugged in
correctly
Remote control is not working
Remote control is not working
Remote control is not linked to
the lamp
Heavy traffic on a wireless data
network (e.g. wireless router)
"I" button wasn't pressed long
enough
The LivingColors lamps belong to
different versions
The sweep movement was not
correct
Other problem
slip or receipt) stating the purchase date, the name of the dealer and a
description of the product.
16.5W AC only The Philips warranty lapses if:
- Anything has been changed, crossed out, deleted or rendered
illegible on the purchase docket or product description.
- Failures caused by damage, faulty connections or abuse.
- A defect is caused by extreme circumstances not inherent to the
LivingColors, for example, lightning, flooding, fire, incorrect use or
negligence.
- The LivingColors has been opened or disassembled.
2405–2475 MHz Warranty and service:
IEEE 802.15.4) For your information and in case of any problems, please visit the Philips
channels 11, 15, 20 or 25 website at www.philips.com/livingcolors or contact Philips Lighting
Contact Center free of charge in U.S.: 800-825-5844
32...104°F (0...40 °C) This device complies with Part 15 of the FCC Rules. Operation is
-13...140°F (-25...60 °C) subject to the following two conditions: (1) this device may not cause
5...95 % non condensing harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Solution
Check the connections of the cord to the lamp
Check that the plug is correctly placed in the wall socket
See the following section
Check the batteries in the remote control. The batteries should
be correctly placed (+ and -) and should be charged. If the
remote control is still not working, try replacing the batteries.
Link the remote to the LivingColors lamp by following the
procedure under "2. Linking LivingColors lamps"
Move LivingColors away from the wireless access point
Make sure that all LivingColors connected to this remote are
on; otherwise they will not respond after this action.
Press simultaneously on "0" and ( ) for at least 5 seconds
to switch to another channel (all LivingColors will flash green
to confirm). You can repeat this procedure up to 3 times,
preferably from another position.
Redo the procedure under "2. Linking LivingColors lamps". If
it was linked successfully, the lamp will give 1 green flash; if the
linking was unsuccessful it will revert to its previous settings
immediately without flashing green.
Check if the lamps you cannot link both have a "G2" sign on the
back of the remote control and at the bottom of the lamp itself.
If one of the lamps does not have it, it cannot be linked with
another lamp that does (but it can still be linked with other
lamps that do not have the G2 sign).
If the color changes to another (static) color, but no color loop
starts, then your sweep movement was not correct; please try
again
Contact the Philips Lighting Contact center (see Warranty and
Service)
3
11/6/2012 11:06:10 AM