Technical Data; Noise/Vibration Information; Declaration Of Conformity - Bosch PFS 105 E WALLPaint Manual Original

OBJ_BUCH-1543-001.book Page 15 Friday, November 18, 2011 9:16 AM
8 Hose port (spray gun)
9 Trigger switch
10 Container for spray material
11 Handle extension
12 Suction tube
13 Container seal
14 Rotating ring
15 Nozzle cap
16 Nozzle needle
17 Nozzle seal
18 Air hose
19 SDS connector
20 Protective cap for SDS connector
21 Base unit
22 Accessory compartment
23 Air filter cover
24 Control knob for On/Off and air-flow control
25 Set-down port for spray gun
26 Hose connection (base unit)
27 Carrying handle
28 Filling funnel
29 Air filter
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.

Technical Data

Fine-spray System
Article number
3 603 B06 ...
Rated power input
Spraying capacity g/min 200–350 200–350
Atomising output
Required time for applica-
2
tion of paint on 5 m
Container capacity for
spray material
Length of air hose
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 74 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Bosch Power Tools
Vibration total values a
determined according to EN 60745:
a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, Dept. PT/ETM9,
D-70745 Leinfelden-Echterdingen
PFS 105 E WALLPaint
Dr. Egbert Schneider
Senior Vice President
... 201 ... 271
Engineering
W 375 375
W 120 120
Robert Bosch GmbH, Power Tools Division
min 2.5 2.5
D-70745 Leinfelden-Echterdingen
Leinfelden, 18.11.2011
ml 1000 1000
Assembly
m 3.40 3.40
kg 5.2 5.2
/II /II
Connecting the Air Hose (see figures A1
– Take the air hose 18 out of the accessory compartment
– Remove the protective caps 20 from both ends of the air
Connecting to the spray gun:
– Firmly insert an SDS connector 19 of the air hose in align-
– Turn the SDS connector until the lock engages.
(triax vector sum) and uncertainty K
h
2 2
< 2.5 m/s , K= 1.5 m/s .
h
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
Before any work on the machine itself, pull the mains
plug.
22.
hose.
ment with the arrow mark into the hose port of the spray
gun 8.
English | 15
A2)
–
1 619 929 K18 | (18.11.11)