Maintenance And Care; Disposal Information; Declaration Of Conformity; Exemption From Liability - Flex L 15-10 150 Instrucciones De Funcionamiento Originales

–
Applying moderate pressure, move the angle grinder
backwards and forwards. As a result, the workpiece will not
become too hot and there will be no discoloration; nor will
there be any grooves.
Cut-off grinding (Figure J)
WARNING!
A special cutting guard must be used for cut-off grinding.
–
Hazardous quartz dust is produced when bricks, concrete
and natural stone are cut.
–
Do not press, tilt or oscillate the power tool.
–
The angle grinder must always be operated backwards,
see diagram.
Otherwise, there is a risk of the angle grinder jumping
uncontrollably out of the groove.
–
Adjust the feed to the material which is to be cut:
the harder the material, the slower the feed.
For further information on the manufacturer's products go to
www.flex-tools.com.

Maintenance and care

WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
Cleaning
WARNING!
If metals are ground or cut over a prolonged period, conductive
dust may become deposited inside the housing. Impairment of
the protective insulation! Operate the power tool via a residual-
current-operated circuit-breaker (tripping current 30 mA).
Regularly clean the power tool and ventilation slots. Fre-

quency of cleaning is dependent on the material and dura-
tion of use.
Regularly blow out the housing interior and motor with dry

compressed air.
Carbon brushes
The angle grinder features cut-off carbon brushes.
When the wear limit of the cut-off carbon brushes is reached,
the angle grinder switches off automatically.
NOTE
Use only original parts supplied by the manufacturer for re-
placement purposes.
If non-original parts are used, the guarantee obligations of the
manufacturer will be deemed null and void.
When the power tool is being used, the carbon brushes can be
seen sparking through the rear air inlet apertures.
If the carbon brushes spark excessively, switch off the angle grin-
der immediately.
Take the angle grinder to a customer service workshop authorised
by the manufacturer.
Gears
NOTE
Do not loosen the screws on the gear head during the warranty
period. Non-compliance will deem the guarantee obligations of
the manufacturer null and void.
14
L 15-10 150 / L 21-6 230 / L 21-8 180 / L 2200
Repairs
Repairs may be carried out by an authorised customer service
centre only.
Spare parts and accessories
Other accessories, in particular sanding tools and cutting gu-
ards, can be found in the manufacturer's catalogues.
Exploded drawings and spare-part lists can be found on our
homepage: www.flex-tools.com

Disposal information

WARNING!
Render redundant power tools unusable by removing the po-
wer cord.
EU countries only
Do not throw electric power tools into the household
waste!
In accordance with the European Directive 2012/19/EU
on Waste Electrical and Electronic Equipment and
transposition into national law used electric power tools
must be collected separately and recycled in an env-
ironmentally friendly manner.
NOTE
Please ask your dealer about disposal options!

-Declaration of Conformity

We declare under our sole responsibility that the product des-
cribed under page 5 conforms to the following standards or nor-
mative documents:
EN 60745 in accordance with the regulations of the directi-
ves 2014/30/EU 2006/42/EC, 2011/65/EU.
Responsible for technical documents:
FLEX-Elektrowerkzeuge GmbH, R & D
Bahnhofstrasse 15, D-71711 Steinheim/Murr
03.07.2017
FLEX-Elektrowerkzeuge GmbH
Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The manufacturer and his representative are not liable for any
damage and lost profit due to interruption in business caused
by the product or by an unusable product.
The manufacturer and his representative are not liable for any
damage which was caused by improper use of the power tool
or by use of the power tool with products from other manufac-
turers.