Noise/Vibration Information - Wurth Master BMH 32-XE Manual De Instrucciones

Technical Data
Rotary Hammer
Art. No.
Rated power input
Rated speed
Impact rate
Impact energy per stroke
Chisel positions
Tool holder
Lubrication
Max. drilling dia.
– Concrete (with twist drill)
– Brickwork (with core bit)
– Steel
– Wood
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given apply for nominal voltages [U] of
230/240 V.

Noise/Vibration Information

Measured values
EN 60745.
Typically the A-weighted noise levels of the product
are: Sound pressure level 93 dB(A); Sound power
level 104 dB(A). Uncertainty K =2 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Hammer drilling into concrete: Vibrational emission
2
value a =10 m/s , uncertainty K=1.5 m/s
h
Chiselling: Vibrational emission value a
uncertainty K=1.5 m/s
Drilling in metal: Vibrational emission value
2
a <2.5 m/s , uncertainty K=1.5 m/s
h
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different acces-
sories or poorly maintained, the vibration emission
may differ. This may significantly increase the expo-
sure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the
exposure level over the total working period.
3.3.09
BMH 32-XE
0702 543 X
W
-1
min
-1
min 0–3600
J
SDS-plus
Central
permanent
lubrication
mm
mm
mm
mm
kg
determined according
2
=9 m/s
h
2
,
2
.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
900
Declaration of Conformity
0–760
We declare under our sole responsibility that the
5.0
product described under "Technical Data" is in con-
12
formity with the following standards or standardiza-
tion documents: EN 60745 according to the
provisions
98/37/EC (until 28 Dec 2009), 2006/42/EC (from
29 Dec 2009).
Technical file at:
32
Adolf Würth GmbH & Co.KG, PFW,
90
D-74650 Künzelsau
13
Künzelsau, 06.02.2009
32
Adolf Würth GmbH & Co. KG
4.7
/II
P. Zürn
to
❏ Before any work on the machine itself,
pull the mains plug.
❏ Operate your machine only with the auxil-
iary handle 10.
The auxiliary handle 10 can be set to any position
for a secure and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 10 in
,
counterclockwise direction and swivel the auxiliary
2
,
handle 10 to the desired position. Then retighten the
bottom part of the auxiliary handle 10 by turning in
clockwise direction.
Adjusting the Drilling Depth
(see figure A)
The required drilling depth X can be set with the
depth stop 11.
Press the button for the depth stop adjustment 9 and
insert the depth stop into the auxiliary handle 10.
Insert the SDS-plus drilling tool to the stop into the
SDS-plus tool holder 1. Otherwise, the movability of
the SDS-plus drilling tool can lead to incorrect
adjustment of the drilling depth.
Pull out the depth stop until the distance between the
tip of the drill bit and the tip of the depth stop corre-
spond with the desired drilling depth X.
The knurled surface of the depth stop 11 must face
downward.
of the directives
A. Kräutle
Auxiliary Handle
2004/108/EC,
English–13