Publicidad
inserire il codice 116 e premere P1; si udrà un
tono di conferma ed il led rosso inizierà a
lampeggiare;
comporre l'indirizzo 201 se la pulsantiera invia
chiamate ad 1 o più centralini principali
oppure l'indirizzo 210 se la pulsantiera invia
chiamate ad 1 o più centralini secondari; per
non inviare chiamate a centralini comporre
255;
premere P1; si udrà un tono di conferma ed il
led rosso tornerà ad accendersi in modo
continuo;
proseguire inserendo il codice di una nuova
programmazione o uscire spostando il
ponticello
nella posizione 1-2.
J6
000. Ritorno alla programmazione di fabbri-
ca
Dopo essere entrati in modalità programmazio-
ne come descritto nel relativo capitolo, occorre:
comporre 000 seguendo le indicazioni del
capitolo "immissione codici o indirizzi";
premere P1; si udirà un tono di conferma ed il
led rosso inizierà a lampeggiare;
comporre 123 seguendo le indicazioni del
capitolo "immissione codici o indirizzi";
premere P1; si udirà un tono di conferma e
lampeggieranno brevemente i led bianchi del-
la telecamera;
uscire dalla programmazione
ponticello
J6
da 2-3 a
1-2.
Attenzione. Dopo aver eseguito questa proce-
dura tutti i valori di programmazione sono ripor-
tati ai valori di fabbrica.
Tabella 2
Per facilitare la programmazione e per
ricordarla in seguito si consiglia di scrivere
gli indirizzi nella tabella seguente
Codici
Indirizzi
Valori da.. a..
111
- - -
231 ÷ 250
112
- - -
001 ÷ 200
113
- - -
001 ÷ 200
114
- - -
001 ÷ 010
116
- - -
201 / 210
EN
PROGRAMMING
Following is a list of default settings. If necessary,
follow the instructions contained in the next chap-
ters to change them.
Factory setting
-
External Door Station Address = 231
- Address associated with P1 button = 100
- Address associated with P2 button = 101
- Lock actuation time = 1 second
Entering the programming mode
Remove the plate.
Move the jumper J6 from position 1-2 to 2-3;
you hear the programming tone and the red
LED turn ON (R).
2-3
Programming
mode
3
2
1
spostando il
J6
3
2
1
J6
1-2
Operating
mode
Exit the programming mode
To exit the programming mode, you must bring
the jumper J6 from position 2-3 back to position
1-2.
Using the push-buttons for programming
Press button "P1" and "P2" to enter addresses
or codes.
Press this button to confirm code
Pn:
programming or go to the next
programming step.
Press this button to increase the value
P1:
you want to enter. Press the button for a
nu
mber of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = press "P2" 10 times).
The pressure of the "P2" button is confirmed by
an acoustic tone on the loudspeaker.
Entering codes or addresses
- Codes and/or addresses must have three
- Enter one digit at a time by pressing the "P2"
R
Note: - remember to confirm the codes you have
Table 1.
3
Programming codes
2
1
111 External Door Station address
J6
112 P1 button address
S+
S-
PB GN
113 P2 button address
114 Door lock activation time
116 Operation with door keeper exchangers
000 Back to factory settings
Programming procedure
To make the programming it necessary to:
a) enter the programming mode following the
b) enter the three digits of the programming
c) make the operations described in the
d) continue with another programming operation
111. Entering the External Door Station
address
In this mode you can code the external door
station address with codes from 231 to 250
(default is 231).
P1
button P1
P2
button P2
digits (hundreds, tens, units); codes and/or
addresses with tens and units or units only
must be completed by adding zeros. For
example, address 96 becomes 096 and
address 5 becomes 005.
button for a number of times "n", where "n" is the
value of the digit you want to enter, followed by
a pause of about 2 seconds before you go to
the next digit (a tone on the
loudspeaker
you when to go to the next digit). The maximum
value you can enter is 255. For example, to
enter code 096 you must:
- press the "P2" button 10 times to enter digit
0 and wait for 2 seconds until you hear a tone
in the loudspeaker.
- press the "P2" button 9 times to enter digit 9
and wait for 2 seconds until you hear a tone on
the loudspeaker.
- press the "P2" button 6 times to enter digit 6
and wait for 2 seconds until you hear a tone on
the loudspeaker.
entered as explained in the programming
chapters.
instructions described in "Entering the
programming mode";
code you want to change following the
instructions contained in "Entering codes or
address"; press P1 to confirm: you hear the
confirmation tone and the red LED start
flashing.
specific programming chapter.
or exit moving the jumper J6 from 2-3 to 1-2.
Enter the programming mode following the
instructions described in "Entering the pro-
gramming mode";
Enter code 111 and press P1; you hear a
confirmation tone and the red LED start flash-
ing.
Dial the code number you have chosen for the
external door station and press P1 to confirm;
you hear the confirmation tone and the red
LED go back ON without flashing.
Mi 2495
will tell
- 7 -
Publicidad
