Installation; Switching On The Appliance; Setting The Temperature - Siemens KA N Serie Instrucciones De Uso

en

Installation

Installation location
Install the appliance in a dry, well venti
lated room. The installation location
should neither be exposed to direct
sunlight nor near a heat source, e.g. a
cooker, radiator, etc. If installation near
a heat source is unavoidable, use a
suitable insulating plate or observe the
following minimum distances to a heat
source:
- 3 cm to an electric cooker.
- 30 cm to an oil or solid fuel cooker.
The floor on which the appliance is to
be installed must be rigid. If required,
reinforce the floor.
The appliance is very heavy, for empty
weight see the following table.
Basic model
Model with dispenser
Model with home bar
To ensure that the ice maker functions
correctly, the appliance must be up
right. Align the appliance with a spirit
level. To ensure that the doors can
open all the way, observe lateral mini
mum distances when installing the
appliance in a corner or recess (see
section on Appliance dimensions").
Installing and connecting
the appliance
Have a technician install the
appliance and connect it to the
water supply according to the
enclosed installation instructions.
After installing the appliance, wait at
least ½ hour before switching on the
appliance. During transportation the oil
in the compressor may have flowed
into the refrigeration system.
Before switching on the appliance
for the first time, clean the interior of
the appliance (see Cleaning the
appliance").
28
Electrical connection
Do not use an extension lead or a
multi plug socket. This appliance
must be connected to a permanently
installed socket.
The plug to secure the appliance must
be freely accessible. Connect the
appliance to a 220 240 V/50 Hz AC
current via a plug which has been
properly installed. The plug must be
fitted with a 10 A fuse or higher.
If the appliance is to be operated in
a non European country, check on
the rating plate whether the indica
ted voltage and current type corres
pond to the values of your mains
supply. The rating plate is situated
in the bottom left hand side of the
appliance. Any necessary exchan
ging of the mains lead should car
ried out by a specialist electrician.
Warning!
!
104 kg
Never connect the appliance to
electronic energy saver plugs
113 kg
(e.g. Ecoboy, Sava Plug) or to power
115 kg
inverters which convert the direct
current to 230 V alternating current
(e.g. solar equipment, power
supplies on ships).
Observe ambient
temperature and ventilation
The atmosphere grade is written on the
identification plate. It states the room
temperature within which the appliance
can be operated.
Atmosphere grade
SN
N
ST
T
Ventilation
Never cover the ventilation openings in
the base panel. Otherwise, the refrige
rating unit must work harder and the
power consumption is increased.
Switching on
the appliance
S Insert the mains plug into a socket.
The appliance begins to cool down as
soon as it is connected to the power
supply. When the doors are open, the
interior lights come on.
Note:
The preset temperatures (factory
settings) are reached after approx. 2 to
3 hours. Do not put any food in the
appliance beforehand.
To change the set temperatures > see

Setting the temperature".

Setting the
temperature
Appliances with control
panel
- The temperature for the refrigerator
- The factory setting for the refrigerator
- The factory setting for the freezer
To change the values:
S Keep pressing the Selection button
Permitted ambient
temperature
+10 °C to 32 °C
+16 °C to 32 °C
+16 °C to 38 °C
+16 °C to 43 °C
The value last indicated is saved by the
system.
and freezer compartments can be
adjusted separately. The set value
is indicated on the display panel.
compartment is 4 °C.
compartment is 19 °C.
until the required temperature value is
indicated.