Install The Door Control - Sears Craftsman 139.53992 Manual Del Propietário

WARNING
INSTALLATION STEP 7
CAUTION

Install the Door Control

Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, away from moving parts of door and door
hardware. If installing into drywall, drill 5/32" (0.40 cm)
holes and use the anchors provided. For pre-wired
installations (as in new home construction), it may be
AVERTISSEMENT
mounted to a single gang box (Figure 2).
1. Strip 7/16" (11 mm) of insulation from one end of
ATTENTION
bell wire and connect to the two screw terminals on
back of door control by color: white wire to 2 and
white/red wire to the 1.
2. Remove white cover by gently prying at slot in top
of the cover with a small flat head screwdriver.
Fasten with 6AB x 1-1/4" self-tapping screws
(drywall installation) or 6-32 x 1" machine screws
(into gang box) as follows:
• Drill and install bottom screw, allowing 1/8" (3 mm)
to protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not over tighten.
• Insert top tabs and snap on cover.
3. (Standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not
pierce wire with a staple, creating a short or open
circuit. If your access door is near the garage door,
you may run this wire with the Safety Reversing
Sensor wires along the top of the rail. See page 18.
4. Insert all wires through the opening on top of motor
unit above the terminal block on the back panel
(Figure 3).
5. Strip 7/16" (11 mm) of insulation from each set of
wires. Insert door control wire into quick-connect
terminals by color: white wire to white, white/red
wire to red.
Separate white and white/black wires sufficiently to
connect to the opener quick-connect terminals. Twist
like colored wires together. Insert wires into quick-
connect holes: white to white and white/black to
grey.
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires
into quick-connect holes: white to white and red/white
to red.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
NOTE: DO NOT connect the power and operate the
opener at this time. The trolley will travel
to the full open position but will not return
to the close position until the sensor
beam is connected and properly aligned.
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of
reach of children at a minimum height of 5 feet, and
away from all moving parts of door.
• NEVER permit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely
closed. NEVER permit anyone to cross path of closing
garage door.
6AB x 1-1/4" Screw
(drywall installation)
6-32 x 1" Screw
(gang box installation)
Outside Keylock Accessory Connections
To opener quick-connect terminals: white to white;
white/red to red.
PREMIUM
CONTROL
CONSOLE
Lighted
Push
Button
Figure 1
REMOVE & REPLACE COVER
To Replace,
Insert Top
Tabs First
Figure 3 Wiring to Terminal Block
Strip 7/16" (11 mm) of insulation from each wire.
Insert wires through opening on top of motor
unit above terminal block, then into quick-
connect terminals.
Door Control
Connections
7/16"
(11mm)
Strip wire 7/16" (11mm)
Red White
21
WARNING
WARNING
AVERTISSEMENT
AVERTISSEMENT
Hardware Shown Actual Size
WHITE
2
Light
Lock
BACK VIEW
Figure 2
PRE-WIRED
INSTALLATION
To Remove,
Twist
Here
To release wire, push in tab
with screwdriver tip
Grey
/
Insulated
Staples
Dry Wall Anchors
Top
Mounting Hole
Terminal
Screws
RED
1
Bottom
Mounting Hole
24 Volt
2-Conductor
Bell Wire in
Gang Box
To
To
Sensors
Door
Control
Quick-
Connect
Terminal