Technical Data - Cloer ART-6980 Manual Del Usuario

Fundamental safety notes
• This device is exclusively intended to be used in the household and similar applications, as for
example:
- in kitchens for employees in shops and offices,
- in agricultural properties,
- by clients in hotels, motels and other residential facilities or
- in bed and breakfast accommodations.
• Let repairs of Cloer electrical appliances only be carried out by authorized Cloer specialist
dealers or by the Cloer service center. Substantial dangers for the user can result through
improper repairs. Your warranty claim expires additionally.
• Operate the device only at domestic sockets. Check whether the mains voltage indicated on
EN
the type plate matches the voltage of your power supply.
• If the connection line is damaged, it must be replaced by an authorized Cloer specialist dealer
or the Cloer service center, in order to avoid endangerments.
• The device must always be separated from the power supply with a lack of supervision and
before assembly, disassembly or cleaning.
• Pull the power plug from the socket
- if a fault occurs.
- if the device is not used for a longer period of time.
• Please only pull on the plug, never on the line.
• Do not stretch the line too tightly, as otherwise there is a risk that the device tips.
• Do not pull the line across sharp edges.
• Do not use the line for carrying and protect it against heat (hot plate / open flame).
• This device should not be used by children. The device and its connection line must be kept
away from children.
• Children may not play with the device.
• Devices can be used by persons with reduced physical, sensory or mental abilities or lack of
experience and/ or knowledge, if they are supervised or instructed concerning the safe use of
the device and have understood the dangers resulting therefrom.
• Do not use the device in the open air.
• Never immerse the device in water.
• Caution while handling the sharp cutting knives as well as while emptying the container
and while cleaning.
• Clean all surfaces/parts which came into contact with food after use of the device. You can find
further notes for cleaning on the following pages.
• The appliance must be switched off previously and disconnected from the mains before
replacing any components or parts, that are moved during the process.
• Power supply, cable or plug should not get wet in any case.
• Improper use of the vacuum blender could lead to injuries.
12

Technical Data

Typ Volt Hz Watt
6980 220-240 50-60 800
Before the first use
Read these instructions carefully
and retain for future reference.
• Remove all packing parts and possible stickers, not
the type plate.
• Place the Vacuum Blender on a dry, slip-resistant and
even base.
• Due to hygienic reasons, it is recommended to use
the cleaning program "Clean" for the first time. In or-
der to do this, fill the recipient up to the "max" mark
with water and a drop of dishwashing detergent.
• Rinse the recipient again with clear water.
• Finally, pour this water away.
CE labeling / Safety notes
The device corresponds to the
requirements of the applicable EC
guidelines.
The device is exclusively intended for
use in closed rooms.
ATTENTION! Unplug from outlet
when not in use and before cleaning!
ATTENTION: The operation is only
possible with the container correctly
placed
Assembly of the vacuum blender
Assemble Blending jar:
• Start with the assemble lid.
• First, install the vacuum valve and the blender jar cover.
Install vacuum valve and blending jar lid
pad to blending jar lid first.
Install blending jar seal to blending jar
lid and then install lid filter by rotating
clockwise.
• Press blending jar lid down to blending jar by alig-
ning lid tip with jar spout.
Assemble blade set:
• Rotate blade set anti-clockwise and install to blen-
ding jar.
Assemble vacuum storage jar:
Install vacuum valve and storage jar seal
to vacuum storage jar.
Then install lid filter by rotate clockwise.
Press storage jar lid down to vacuum
storage jar.
Starting up
Before the extraction of the blending jar:
• Do not operate the appliance with a damaged cord
or plug or after the appliance malfunctions or is drop-
ped or damaged in any manner.
• Do not let excess cord hang over the edge of a table
or worktop or touch hot surfaces.
• Do not leave the appliance unattended.
• Avoid the contact with movable parts.
• The use of attachments, unauthorized and not sold by
the manufacturer, or discs on base without first putting
blending jar in place may cause fire, electric shock or
injury.
• Do not attempt to defeat the interlock mechanism.
• Do not use the vacuum blender more than 3 minutes.
• Use the vacuum blender to prepare domestic quanti-
EN
13