Perles OF 9 Instrucciones página 15

Fixing router table
Fix the router table to the desired height by the lever
Built-in telescopic spring returns the router table in the
original position after releasing the lever.
Rough depth adjustment
Adjustment must be carried out when the tool
is switched off.
Set the depth of milling by the screws on the chip
deflector , together with the adjusting bit
indicator . The three screws on the chip deflector
enable pre-setting of three depths of milling. The range
of setting is 50 mm.
Put the router on the workpiece.
Release the lever and slowly push down the tool.
When the router touches the surface, pull the lever
Turn the chip deflector
of milling.
Unscrew the wing screw
movement of the adjusting bit
Push down the adjusting bit
screw on the chip deflector.
Set the depth indicator
Push the adjusting bit
desired depth on the scale
Release the lever and push the bit into the new pre-
adjusted position so that the adjusting bit
the screw and then pull the lever
You must check the rough depth adjustment by a
practical test and then correct it if necessary.
Fine depth adjustment
Adjustment must be carried out when the tool
is unpluged.
Carry our fine depth adjustment if necessary. Having set
the rough depth adjustment you can set the desired
depth to 0,1 mm accurately by turning the knob of the
adjusting bit (1 line = 0,1 mm).
First release the lever
down, press the upper button of the adjusting bit in the
direction , so that it is laid on the screw on the
revorverskem nastavku
with the upper one, then turn the upper button in the
direction for a desired value. Pull again the lever
Fine depth adjustment with the router fixed in a
table:
Support the adjusting bit
deflector by a hollow screw and a spring.
Fasten the hollow screw
attention to put the screwdriver in the inside of the
adjusting bit into the groove of the screw below the nut
. Pushing the cover of the tool you set the approximate
depth of cut and fasten the screw
adjustment is carried out by turning the upper lever in the
direction .
Check the accuracy by a practical test or correct it
correspondingly.
Using parallel guide
Fix the parallel guide
the holes in the base plate
desired depth by two wing screws
Use knob for more accurate depth adjustment by
fixing the two wing screws
to the most favourable depth
and thereby you loosen the
.
so that it is set on the
to 0.
upwards. When you reach the
, fasten the wing screw
is laid on
again.
. While you are pushing the tool
. Adjust the lower button
on the screw of the chip
to the adjusting bit
. Fine depth
by inserting the adjusting bits in
, and fasten them to the
.
and loosening wing screws
. Turning the button
close to the guide. When you fully turn the nut, the
.
distance changes by 1,25 mm. Fasten the two screws
after the adjustment.
WORK WITH THE ROUTER
Always check that the supply voltage is the
same
nameplate.
by
Switch on / off
Switch on: Press the lock-off button
the switch lever
Continuous operation: When the tool is switched on,
push further button
button
.
lever and the then the button
Switch off: Pressing again the switch lever
off the tool.
Full wave variable speed (Type OF9E)
Adjusting button
27000 rpm.
Constant electronics
.
Enables milling of all sorts of wood, laminates, plastics
and aluminium
Enables constant set number of revolutions at heavy
loads
Enables setting optimal working revolutions
Prolongs the service lives of routers
Soft start of the tool and overload protection
Enables corresponding adjustment and greater safety
when milling with rezkarji of large diameters.
Recommended table for choosing the number of
revolutions regarding the worked material and bit's
diameter
.
. Pay
Symbols of materials
gypsum boards
aluminium
plastics
panel
15
you are moving the bit away or
as the voltage
,
and lock-off the switch. Press
and lever to the end, then first release the
enables variable speed from 6000 to
indicated on the
, and then press
.
you switch