Publicidad
Idiomas disponibles
Idiomas disponibles
• Risk of explosion – Do not spray flammable liquids.
• Risk of injection or injury to persons – Never direct
discharge stream at people, pets, or electrical devices.
• Disconnect the tool – Disconnect from the electrical power
supply before performing any maintenance task.
• Keep children away – This high-pressure electric
power washer must not be used by children or untrained
personnel.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by the
manufacturer.
m
WARNING!
Water that has flowed through backflow
preventers is considered to be non-potable.
m
WARNING!
During cleaning, maintenance, or when
replacing parts, disconnect the machine from its power source
by removing the plug from the socket outlet.
m
WARNING!
High-pressure hoses, fittings, and
couplings are important for the safe operation of the appliance.
Use only hoses, fittings, and couplings recommended by the
manufacturer.
• Check for damaged parts – Do not use the appliance if
the supply cord or other important parts of the appliance
are damaged (e.g. safety devices, high-pressure hoses,
trigger gun).
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
m
WARNING!
Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and off the
ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe
call the Snow Joe
+ Sun Joe
®
1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, flat surface during operation,
handling, transportation, and storage. Sudden overturn of
the machine can cause bodily injury.
• In the event of an accident or breakdown, switch off the
machine immediately. (If contact with detergent occurs,
rinse with an abundance of clean water.)
+ Sun Joe
dealer or
®
®
customer service center at
®
Electrical Safety
ATTENTION:
If there are problems with the electrical
MAINS, short voltage drops may appear when starting the
equipment. This can, in turn, influence other equipment
(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax
< 0.335 OHM, such disturbances are not expected. (If you
require assistance, contact your local supply authority for
further information.)
m
WARNING!
Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects.
If you find any, do not start up your machine. Contact your
authorized Snow Joe
+ Sun Joe
®
+ Sun Joe
customer service center at 1-866-SNOWJOE
®
(1-866-766-9563).
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a
qualified person.
• The electric supply to this appliance should include either
a residual current device that will interrupt the supply if the
leakage current to the earth exceeds 30 mA for 30 ms or a
device that will interrupt the earth circuit (GFCI).
IMPORTANT:
Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional filter should be installed.
Servicing of Double-Insulated Appliance
In a double-insulated appliance, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated appliance, nor should a means
for grounding be added to the appliance. Servicing a double-
insulated appliance requires extreme care and knowledge
of the system, and should be performed only by qualified
service personnel at an authorized Snow Joe
dealer. Replacement parts for a double-insulated appliance
must be identical to the parts they replace. A double-insulated
appliance is marked with the words "Double Insulation" or
"Double Insulated." The symbol
may also be marked on the appliance.
Safety devices
The unloader valve can reduce pressure if it exceeds preset
values. The spray gun features a locking device. When the lock
is activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor
against overloading. The machine will restart after a few
minutes when the thermal sensor has cooled.
2
dealer or call the Snow Joe
®
+ Sun Joe
®
®
(square within a square)
®
Publicidad
