Using The Device; Cleaning The Device; Technical Data - camry CR 7810 Manual De Uso

I.– temperature increase button
J.– temperature decrease button
K.– timer switch
5.Cord storage
6.Radiant ribs
7.Wheels
8.Remote control
ASSEMBLY (Fig. 2)
1. Turn the heater upside down.
2. Place the wheel bases between the first two ribs and end two ribs.
3. Use the U-shaped clamp to hook the bases.
4. Block the clamp by screwing on the butterfly nut.
5. Place the heater on the wheels.
CAUTION: After turning the heater, wait at least one hour before connecting it to a power outlet.

USING THE DEVICE

CAUTION: During first use of the heater a small amount of smoke may appear. This is normal.
1. Place the oil heater a minimum of 100 cm from walls, furniture, curtains, plants etc. on a flat and stable surface.
2. Make sure that all controls are set to off position. Connect the oil heater to mains power, press the power switch on (2) and then press
power on button (G) to start operation, press both again to stop operation. To turn off the device, press the power button (G) and then press
the power switch (2).
3. Power level setting
After power on the device press mode switch (H) on the control panel (4) to select desired power level low or medium or high by repeated
pressing. The display (3) will light up indicator A or B or C.
4. Temperature setting
The device has a thermostat which enables you to set the temperature from 15°C to 35°C. After setting the desired temperature on the
display of the device, the heating element will remain on until the room temperature reaches the desired temperature. The thermostat will
then cycle on and off to maintain the set room temperature.
Press buttons (I) or (J) on the control panel (3) or on the remote control (8) to set desired temperature in range 15°C - 35°C. The heating
element comes on again when the room temperature drops below the desired temperature.
5. Setting the timer
When the device is powered on. You can set the timer to switch off the appliance automatically after a certain period of time. Press the timer
button (K) several times to set the desired power off time (between 1 and 12 hours from the time the function is set). The display will show
00 and start flashing on the screen. The function will activate once the timer icon stops flashing. The heating element will cycle on and off
as per the set temperature setting and discontinue operation when the set time has run out.

CLEANING THE DEVICE

1. Prior to cleaning always remove the plug from the electrical outlet.
2. Prior to cleaning allow the heater to cool. Make sure that it is cool.
3. Wipe the heater with a damp cloth, then wipe dry.
4. Never use wax, shining agents or chemical agents to clean the heater. They may react with the device and cause discoloration or even
damage.

TECHNICAL DATA

Power source: 220-240V~50/60 Hz
Power levels: ( low / medium / high)
CR 7812: 600W / 900W / 1500W - 7 ribs
CR 7810: 800W / 1200W / 2000W - 9 ribs
CR 7813: 1000W / 1500W / 2500W - 11 ribs
CR 7814: 1000W / 1500W / 2500W - 13 ribs
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins.
Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the
environment. Electrical appliance must be returned in order to reduce its reuse and utilization. If the device contains batteries
they should be delivered to dedicated points separatelly.
ALLGEMEINE SICHERHEITSVORSCHRIFTEN LESEN SIE AUFMERKSAM WICHTIGE
ANWEISUNGEN BEZÜGLICH DER SICHERHEIT DER BENUTZUNG BEWAHREN SIE
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
DEUTSCH
DIESE FÜR DIE ZUKUNFT AUF
7
Device is made in class I of insulation and has to be
connected only to power outlet with ground circuit.
Device is compliant with EU directives:
- Low voltage directive (LVD)
- Electromagnetic compatibility (EMC)
Device marked CE mark on rating label