Bosch Professional GCO 2000 Manual Original página 17

OBJ_BUCH-1063-003.book Page 17 Wednesday, July 3, 2013 1:51 PM
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
Technical Data
Cut off grinder
Article number
3 601 L17 ...
Rated power input
No-load speed
Soft starting
Weight according to
EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximal/minimal) see page 19.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimensions of suitable cutting discs
Cutting disc diameter, max.
Cutting discs width, max.
Mounting hole diameter
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 61029
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 03.07.2013
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the ac-
cessories provided.
Bosch Power Tools
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Cut-off grinder with mounted cutting disc
– Ring spanner 14
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
GCO 2000
that ensure faultless operation.
Damaged protective devices and parts must be immediately
... 20.
replaced by an authorised service centre.
... 27. ... 26.
W 2000 1650
Stationary or Flexible Mounting
-1
min 3500 3500
 To ensure safe handling, the machine must be mounted
 
kg 18 18
Mounting to a Working Surface (see figure A)
/II /II
– Fasten the power tool with suitable screw fasteners to the
Flexible Mounting (not recommended!)
In the exceptional case that it should not be possible to firmly
mm 355
bench-mount the power tool, you can provisionally place the
legs of base plate 12 on a suitable surface (e. g. a workbench,
mm 3
level floor, etc.) without bolting the machine down.
mm 25.4
Changing the Tool (see figures B1
 Before any work on the machine itself, pull the mains
 Actuate the spindle lock 5 only when the tool spindle
 Do not touch the cutting disc after working before it
Use only cutting discs that have an equal or higher maximal al-
lowable speed than the no-load speed of your power tool.
Use only cutting discs that correspond to the characteristic
data given in these operating instructions and are checked ac-
cording to EN 12413 and marked appropriately.
Place unused cutting discs in an enclosed container or in the
original packaging. Store cutting discs lying flat.
Removing the Cutting Disc
– Bring the power tool into the working position. (see "Re-
– Swing back the retracting blade guard 4 to the stop.
– Turn hexagon bolt 24 with the provided ring spanner 14
– Hold the spindle lock pressed and unscrew the hexagon
– Remove the washer 23 and the clamping flange 22.
– Remove the cutting disc 6.
on a level and stable surface (e. g., workbench) prior to
using.
working surface. The mounting holes 11 serve for this pur-
pose.
plug.
21 is stopped. Otherwise, the machine can become dam-
aged.
has cooled. The cutting disc becomes very hot while work-
ing.
leasing the Machine (Working Position)", page 18)
(15 mm) and at the same time press the spindle lock 5 un-
til it engages.
bolt 24.
English | 17
B2)
–
1 609 92A 0CZ | (3.7.13)