Raincover - cam CORTINA X3 TRIS EVOLUTION Manual De Instrucciones

0-6 MONTHS, FITTING THE SHOULDER BELTS:
36. Insert the buckles "s" into slots "S1". WARNING! All the
buckles must be passed through the material slots and the rigid
structure of the backrest in order to be inserted correctly, as
shown in the diagrams.
37. FITTING THE WAIST BELT: insert buckles "a" in slots "A".
38. FITTING THE CROTCH STRAP: insert buckle g" in "G1".
WARNING! Before use, check that the belts are not twisted and
that they are secured properly.
39. CORRECT FITTING OF THE BELTS:Fastenthebelt,makesure
thatthetwohooksarefixedinsidethemainbuckleandcheckthat
the baby's legs are positioned one either side of the crotch strap.
WARNING! Always use the 5-point safety harness.
6-36 MONTHS, REMOVING THE BELTS:
40. Remove the belts as shown in the diagram.
41. Fit the 5-point harness taking care that buckles "s"
correspond with "S2" and buckles "g" with "G2"(see point 16a).
0-12 MONTHS, USE OF THE SEAT REARWARD FACING: It is
advisable to use the seat in the rearward facing position to
enable Mum to keep an eye on baby while still young (0-12
months) during walks.
USING THE SEAT UNIT FORWARD FACING: We recommend
using the seat unit forward facing in order to enable to see the
child at all times when he is from 6 to 12 months old. To remove
the seat unit follow points 20-21-22-23.
42. Place the seat unit on the chassis forward facing, making
sure that part L on the chassis (red plastic part) fits together with
the slot on the seat unit (the slot is placed on handle v).
ATTENTION! Make sure that the seat unit is correctly locked to
the chassis; push it down till you hear a "click".
43. Fit the bumper bar on the back part of the armrests, into the
relevant housings. Push down to hear a "click". ATTENTION!
Make sure the bumper bar is correctly fitted. The side with 2
buttons T must be placed towards the backrest.
44. Adjust the hood's plastic fittings in position 2, pushing the
buttons inside the plastic fittings and adjusting line I until
reaching symbol 2. Then insert the hood horizontally into the
front holes of the armrests, pushing until you hear a "click".
45. Lock the adjusting hood's devices to tighten the hood's cover.
46. Place the seat unit cover onto the armrests thanks to the
press studs.
WARNING! Always attach the fabric part of the hood to the
rear part of the backrest.
REMOVING BUMPER BAR AND HOOD WHEN THE SEAT UNIT
IS FORWARD FACING.
47. To remove the bumper bar push down simultaneously the
2 buttons T and then remove it.
48. To remove the hood pull levers U.
USING THE SEAT UNIT REAR FACING: We recommend using
thepushchairwiththeseatunitrearfacingwhenyourchildisfrom
12 to 36 months old. To remove the seat unit follow points 20-
21-22-23 and place it rear facing. ATTENTION! Make sure the
seat unit it's correctly fitted; push it down until you hear a "click".
49. Fit the bumper bar in the front armrests' holes.
ATTENTION! Make sure the bumper bar is correctly fitted: the
side with 2 buttons T is placed downwards.
50. To assemble the hood rear facing: adjust the hood's plastic
fittings in position 1, pushing the buttons inside the plastic
fittings and adjusting line I until reaching symbol 1. Then insert
the hood in the rear holes of the armrests (these holes are the
same ones used to fit the bumper bar forward facing) and push
down to lock the hood until you hear a "click".
WARNING! Always attach the fabric part of the hood to the
rear part of the backrest.
INSTRUCTIONS FOR USE
REMOVING THE REAR FACING BUMPER BAR
51. To remove the bumper bar from one side only, push just 1
of the two buttons T.
52. To remove completely the bumper bar, push the two buttons
T and remove it.
USING AND FITTING THE 5 POINT HARNESS
53. This pushchair is fitted with a 5 point harness. Adjust the
harness around your child's waist.
54.Pushthetonguesontheendsofthewaiststrapintothemainbuckle
andcheckthatthecrotchstrapisplacedbetweenthechild'slegs.
55. To unlock the harness, squeeze the tongues together on one
end of the waist strap and then slide them out of the main buckle.
Proceedasdescribedintheimages.ATTENTION!Usetheharness
atalltimes.Usethecrotchstrapatalltimestogetherwiththewaist
strap. Use the harness at all times when your child can sit alone.
FITTING THE FOOTMUFF
56. Put the footmuff on the seat unit footrest and make it pass
under the bumper bar. Then push down the press studs.
FITTING THE BASKET
The basket is fitted on the lower part of the frame, thanks to the
press studs.
57. The narrower part of the basket must be put near the 2 front
hooks and then fitted thanks to the press studs.
58. Then fit the larger part of the basket on the 2 rear hooks,
thanks to the press studs. ATTENTION: never load the basket
with more than 2 kgs.

RAINCOVER

59. To use the raincover, please refer to the figure.
FOLDING THE PUSHCHAIR
The pushchair can be folded in 2 different ways:
• "fast way", which does not require to remove any component,
and it is suggested for daily movings;
• "compact way", when wheels and hood are removed, and this
is perfect for travelling.
60. To fold the pushchair unlock the plastic adjusters on both
sides of the hood and fold the hood itself.
61. Lift the secondary lock pushing lever A down, operate parts
C on both sides of the handle and push forward; to complete the
fast way of folding the pushchair, grip one of the armrests and
approach it to the handle.
62. With the rear facing seat unit, the hood will be automatically
closed by the pushchair's tubes.
63. To fold the pushchair with the seat unit forward facing, and
then for a more compact folding, fold the hood towards the
inside of the pushchair.
To fold the pushchair in the compact way, you need to proceed
as follows:
64. Remove the rear wheels (follow in the opposite way point n.
6 above mentioned).
65. unlock button M and remove the front wheel pulling spring
A4 in the direction of the arrow; remove at the same time the
rear fork I. Remove the seat unit (fig. 20-21-22-23)
66.Pushdownthefrontaxlebyoperatingthe2buttonsonthesides
67. In the same way push down the aluminium footrest by
operating the 2 buttons on the sides.
68.TofoldthepushchairpullleversCafterhavingdisengagedthe
secondary lock A (fig 4) and push forward. To complete the
compactwayoffoldingthepushchair,operateaslightpressureon
thepushchair,inthedirectionofthearrowsasshowninthefigure.
69. Turn the handle pushing at the same time the 2 buttons B
on the sides until you reach the position shown in the figure.
REMOVING THE COVER FOR CLEANING PURPOSES
70. Detach all press studs placed on the backrest, on the seat
unit and on the armrests. Release the elastic belt under the seat
28