S2Tech MRL100 Manual De Instrucciones página 2

MRL100 / 942 / 699Plus
A1- Instruction Manual
Digital load / weight measuring system
C) 942 Strain Link System composition
Supplied material:
N° 1 942 Strain Link transducer
N° 4 Screws, type M 6x30 8.8 DIN 933
N° 4 Flat Washers M 6, type UNI 6592
N° 8 Fixing M6 nuts
D) How to install 942 Strain Link transducer on lift's structure
1) Strain link 942 and 699 electronics are to be
fixed and installed on the lift frame.
2) Strain link 942 is to be fixed on a flat and clean
surface, without rust, paint grease or oil.
3) Tighten the 4 screws to fix strain link 942 and
use only flat washers.
4) Set electrical connections accordingly to
connection chart of this manual.
5) Ground to earth 699 electronics and respect all
relevant safety and electrical regulations.
6) Feed power supply to STRAINSENTRY and
wait 15 minutes before calibrating.
Notice: The information in this manual is subject to change without notice.S2Tech shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This manual contains information protected by
copyright. No part of this manual may be photocopied, or reproduced in any form, or translated without prior written consent from S2Tech.
S2Tech srl Via Imperia, 28 Milano – ITALY
Tel: +39 02 8910142 Fax: + 39 02 89124848
E) Digital indicator and load limiter model 699 F
Ground to earth the 699 electronics and respect all the relevant safety and electrical regulations.
Once performed all the needed electrical connections feed power supply and wait 15 minutes, before
calibrating. Measurement changes are displayed in tens of the used engineering units.
At 699 power on, or after a reset, display will show in sequence 699F, the firmware release version (i.e.
1.05) and:
 UCAL, if unit is not calibrated or if default data are loaded
 MCAL, if it has been calibrated using the MANU procedure
Supplied material:
N° 1 699 Digital conditioner complete of mating connectors (removable screw terminal), with reference to
N° 2 Fixing screws, type M4 x 12 UNI 7687
N° 2 Nuts, type M4
Perform calibration of the installed MultiRope MRL100 load measuring system when lift's car is at
the lowest floor of the plant.
CE DECLARATION
699 digital conditioner complies with the requirements of the following norms:
EN 61326-1(1997) + A1(1998) + A2(2001) + A3(2003); EN 61000-6-2(2001); EN 61000-3-2(2000) + A2(2005);EN 61000-3-3(1995) + A1(2001); EN 61000-
4-2 (1995) + A1(1998) +A2(2001); EN 61000-4-3(2002) + A1(2002); EN 61000-4-4(1995) + A1(2001) + A2(2001); EN 61000-4-5(1995) + A1(2001);
EN61000-4-6(1996) + A1(2001); EN 61000-4-8(1993)+A1(2001); EN 61000-4-11(2004)
Z:\Manuali\LM MRL100_942_699A1\Traduzioni Maggio 2015\LM MRL_942_699A1 V2r7 UK .docx
e-mail: info@s2tech.it
www.s2tech.it
Terminal board
connection
10
11
12
13
14
15
16
17
18
19
23
24
NOTE: on serial connections (optional, RS485 or CAN), use solely twisted pair
shielded cables, with shield connected to earth at both ends
Code
ER.10
ER.22
ER.23
ER.24
ER.30
ER.70
the ordered configuration
Version : UK 2r7 dated 25/06/15
Page: 2/4
Type Meaning
1 Screw Terminal GND (DC POWER SUPPLY )
2 Screw Terminal + 24 V (DC POWER SUPPLY)
3 Screw Terminal EARTH connection
4 Screw Terminal CONTACT I/O 2 (option)
5 Screw Terminal CONTACT I/O 1 (Chain compensation - option)
6 Screw Terminal I/O CONTACT's common reference (option)
7 Screw Terminal Relay 3 - Normally Open contact (option)
8 Screw Terminal Relay 3 - Normally Closed contact (option)
9 Screw Terminal Relay 3 Common contact (option)
Screw Terminal Relay 2 - Normally Open contact
Screw Terminal Relay 2 - Normally Closed contact
Screw Terminal Relay 2 Common contact
Screw Terminal Relay 1 - Normally Open contact
Screw Terminal Relay 1 - Normally Closed contact
Screw Terminal Relay 1 Common contact
Screw Terminal + power supply to transducer
Screw Terminal - power supply to transducer
Screw Terminal + signal form transducer
Screw Terminal - signal from transducer
Screw Terminal AGND (Analog output)
Screw Terminal Analog Output
.
Meaning
OVER RANGE - Verify the mechanical fixing of 942 strain
link. Try to substitute the 942 and re-calibrate.
High load sensitivity. Fix 942 to a more rigid part of the lift
frame or substitute it.
HI value is too low (in engineering units).
Load specimen is too low. Increase load.
Damaged A/D converter. Substitute 699 Electronics.
Electrical connection problem. Check connections and that
cable has not been damaged.