Stanley BF01ALT Manual De Instrucciones página 3

– Do not operate the light near flammable liquids or in gaseous or explosive atmospheres.
Internal sparks may ignite fumes causing personal injury.
– Do not expose this unit to extremely high temperatures, flames or sparks.
• To reduce the risk of injury, close supervision is necessary when the light is used near children.
• Store idle appliances indoors. When not in use, appliances should be stored indoors in dry and
high or locked-up places – out of reach of children.
• Use of accessories and attachments. Use only attachments recommended or sold by the
manufacturer.
• Check for damaged parts. A part that is damaged should be properly repaired or replaced by
manufacturer before further use unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by manufacturer. Do not use this appliance if the light mode
button does not turn it on and off.
• Do not operate this unit with a missing or damaged light tube.
• Do not touch the light tube surface at any time.
• Never look directly into the light or shine the light into another person's eyes.
• Do not disassemble the main body of the unit. Other than the dry cell batteries, there are no user-
replaceable parts.
ALKALINE BATTERY SAFETY INSTRUCTIONS
WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:
• Carefully follow all instructions and warnings on the battery label and package.
• Always insert batteries correctly with regard to polarity (+ and –), marked on the battery and
the equipment. Failure to insert batteries in the correct polarity, as indicated in the battery
compartment, may shorten the life of the batteries or cause batteries to leak.
explosion if batteries are incorrectly replaced.
• Do not short battery terminals.
• Do not charge batteries.
• Do not mix old and new, alkaline and rechargeable (nickel cadmium or nickel metal hydride)
batteries. Replace all of them at the same time with
• Remove dead batteries immediately and dispose of per local codes.
• Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
• Remove batteries if the device will not be used for several months.
"Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US Department
of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in
commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries, make sure that the battery
BF01ALT_Manual_ENSP_041716.indd 4-5
There is a danger of
new batteries of the same brand and type.
4
terminals are protected and well insulated from materials that could contact them and cause a short
circuit."
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new
Stanley
follow the instructions carefully before use.
POWER SUPPLY
The unit is powered by three "AA" alkaline dry cell batteries (may be sold separately). Unscrew the
base cover screw (counter-clockwise) and remove the base cover. Insert batteries as described in
compartment, observing all warnings regarding batteries in the Important Safety Instructions section
of this manual. Replace and secure the base cover by screwing the base cover screw clockwise. Do
not be over-tighten.
IMPORTANT: Use only "AA" alkaline dry cell batteries in this unit.
OPERATING THE WORK LIGHT
• Position the unit as desired. Press the light mode pushbutton on the front of the unit.
• Press once for high intensity.
• Press again for medium intensity.
• Press a third time for to turn the light off.
• Press and hold the light mode pushbutton for about five seconds for flashing LEDs.
Adjusting the pivot tube
The pivot tube allows the light to be tilted backward and forward to direct the illumination upward
or downward.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• Do not attempt to "force" the pivot tube beyond its maximum angle.
• The pivot tube was designed to tilt forward and backward only.
• The pivot tube was designed to be used when the unit is hanging or attached to a surface using
its magnetic base. Using it when the unit is placed on a level, non-metallic surface may cause the
light to fall over and sustain damage.
• NEVER attempt to rotate the light tube itself. Always use the pivot tube to adjust the area of
illumination.
Using the hanging hook and magnetic base
The hanging hook and magnetic base allow you to position the light for convenient, hands-free
operation. The hanging hook rotates 360° to direct illumination as needed.
. Read this Instruction Manual and
Work Light
®
5
4/17/2016 11:59:48 PM