Descargar Imprimir esta página
Campbell Hausfeld VT273201AJ Instrucciones De Instalación Y Manual De Piezas
Campbell Hausfeld VT273201AJ Instrucciones De Instalación Y Manual De Piezas

Campbell Hausfeld VT273201AJ Instrucciones De Instalación Y Manual De Piezas

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Instructions and Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product
described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for future reference.
Description
This head replacement kit is for all
Campbell Hausfeld VT twin cylinder air
compressor models. This kit includes the
entire valve plate, valving, head, gaskets
and all associated fasteners.
For Repair Parts, call 1-800-543-6400
Please provide following information:
- Model number
- Serial number (if any)
- Part description and number as shown in parts list
F
5
D
E
B
C
A
6
4
3
9
2
1
Figure 1 - Repair Parts Illustration
© 2012 Campbell Hausfeld/Scott Fetzer
Installation
1. Remove old head and valve plate by
removing the six head bolts.
2. Scrape any old gasket residue from
the top of the cylinder with a gasket
scraper.
NOTE: No gasket sealant required.
3. Place the new valve plate, head and
gaskets onto the cylinder as shown.
Make certain the two center holes are
aligned on all parts (See Figure 1).
Repair Parts List
7
Ref.
No.
Description
1
Cylinder gasket
2
Valve plate assembly
3
Valve plate gasket
4
Cylinder head
8
5
M8 x 150 HHC Screw
6
M8 x 50 HHC Screw
7
Filter housing cover with element
8
Filter element
9
O-ring
Valve plate kit
n
Cylinder head and fastener
l
NOTE: On pump series VT2326 you will need to use ST074302AV,
5/16 - 18 x 6 inch HHC Head Bolts (quantity of 6) and MP513901AJ Unloader Tube
Kit. Depending on original model a new Check Valve may be required.
For parts, product & service information
visit www.chpower.com
Cylinder Head
Repair Kit
4. Install screws (Ref. No. 6- Qty. 2) with
5. Insert the remaining four head screws
AIR FILTER
1. Install the air filter into the 1/2 inch
Address parts correspondence to:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
VT273201AJ
the o-ring exactly as shown in Figure
1.
and torque all the screws to 200
in-lbs. Follow the torque sequence A,
B, C, D, E, & F shown in Figure 1.
intake port on the cylinder head.
Part
No.
n
n
n
l
l
l
VH901700AV
VT901800AV
VT036700AV
VT491100AV
TQ900800AJ
IN220503AV 5/12
Qty.
1
1
1
1
4
2
1
1
1

Publicidad

loading

Resumen de contenidos para Campbell Hausfeld VT273201AJ

  • Página 1 1. Remove old head and valve plate by This head replacement kit is for all removing the six head bolts. Campbell Hausfeld VT twin cylinder air 5. Insert the remaining four head screws 2. Scrape any old gasket residue from compressor models.
  • Página 2 HHC ST074302AV 5/16 - 18 x 6 po (Qté 6) et de la trousse de tuyau de décharge MP513901AJ. Selon le modèle d’origine, un nouveau clapet de non-retour peut s’avérer nécessaire. Figure 1 -Illustration de Pièces Dètachées IN220503AV 5/12 © 2012 Campbell Hausfeld/Scott Fetzer...
  • Página 3 5. Colóquele los cuatro tornillos de aire con doble cilindro VT de restantes, apriételos con un torque de NOTA: No requiere sellador de Campbell Hausfeld. Este juego incluye 200 pulg.lbs. Para aplicarles el torque empaques. toda la placa de la válvula, las válvulas, siga la secuencia A, B, C, D, E, &...
  • Página 4 VT273201AJ Notes/Notas...