General Operation; Radio Operation - Lenco CS-341 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 9

GENERAL OPERATION

1. Switching on/off the unit
Press " PWR " button (22) to power on/off the unit.
2. Remove the panel
Press
button(1) to Remove the panel.
3. Sound adjusting
Press SEL button (2) shortly to select the desired adjustment mode. The adjustment mode will change in the
following order: VOL---BASS---TREBLE---BALANCE---FADER.
By rotating the audio knob (2) clockwise or counter-clockwise, it is possible to adjust the sound setting.
4. LOUDNESS on/off
Press BND/LOU/ENT button (19) for 2 seconds to enable loud mode. Press it for 2 seconds again to disable this
function.
5. LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display.
6. AUXILIARY INPUT
The unit can be connected to a portable audio player through the AUX IN jack (23) on the front panel. After finishing
the connection, you can press MOD button (20) on the front panel to switch the mode to AUX IN mode.
7. RESET FUNCTION
RESET button (24) must be activated with either a ballpoint pen or thin metal object. The RESET button has to be
activated for the following reasons:
-
Initial installation of the unit when all wiring is completed.
-
All the function buttons do not operate.
-
Error symbol on the display.
Note: if press RESET button (24), All the memory will be lost!

RADIO OPERATION

1. SWITCHING TO RADIO MODE
Press MOD button (20) shortly to select radio mode, the radio mode appears in the display together with the
memory band and frequency.
2. SELECTING THE FREQUENCY BAND
At radio mode, press BND/LOU(ENT) button (19) shortly to select the desired band.
The reception band will change in the following order: FM1--FM2--FM3--AM1--AM2.
3. SELECTING STATION
Press
button (18) or
button (4) shortly to search manual. Every time
will change with 0,05 Mhz. Press and hold button
autoscan puch
and
together at the same time.
4. AUTOMATIC MEMORY STORING & PROGRAM SCANNING
-
Automatic memory storing
Press AS/PS (SCH) button (21) for several seconds, the radio searches the signal strength until one cycle
search is finished. And then the 6 strongest stations are stored into the corresponding preset number button.
-
Program scanning
Press AS/PS (SCH) button (21) shortly to preview all the preset stations.
OPERATION
or
is pressed the frequency
or
for 2 seconds to scan automatically. To stop the
4
5. MANUAL STORING A STATION
Tune to a preffered frequency and press one of the preset button(12/13/14/15/16/17) for several seconds, current
station is stored into the number button.
6. RDS (RADIO DATA SYSTEM) OPERATION
-
Setting AF mode
Press AF(REG) button (6) and release immediately to switch on or off AF mode.
Whenever AF is switch on, symbol "AF" appears on the display.
Program name is displayed on receiving a RDS station.
"AF" starts blinking if the broadcasting signal getting worse. And when the signal is too bad due a frequency
change. AF will automatically switch to the new frequency.
-
Regional Program Operation
Press AF(REG) button (6) for several seconds to switch on or off region mode.
Some broadcasting stations change their program from normal broadcasting to regional broadcasting for a
certain time period. When region is on, the current listening program remains unchanged. When region is off, it
allows the reception moves to the regional station.
-
Using PTY to Select Program
PTY button (5) 1 time.then press preset button(12/13/14/15/16/17). You can select the program type as below:
1# button: NEWS/AFFAIR/INFORM
2# button: EDUCATIO/DRAMA/SPORT
3# button: VARIED/CULTURE/SCIENCE
4# button: ECONOMY/CHILD PR/WEATHER
5# button: PHONE IN/SOCIAL/RELIGION
6# button: TRAVEL/LEISURE/DOCUMENT
PTY button (5) 2 time.then press preset button(12/13/14/15/16/17). You can select the program type as below:
1# button: ROCK MUS/POP MUSI
2# button: LIGHT MU/EASY MUS
3# button: OTHER MU/CLASSICS
4# button: COUNTRY/JAZZ MUS
5# button: NATIONAL/OLDIES
6# button: FOLK MUS
-
Listening to Traffic Announcement
TA button (3) is operated as follows:
When pressed, it is engaging whether TA mode on or off.
When TA mode, is on and a traffic announcement is transmitted:
When the unit was in CD (MP3) USB/SD mode or AUX IN mode, it will switch temporarily to radio mode.
If the volume level was under the threshold point it will be raised to the threshold point. But when changed the
volume level, which was more than the threshold point (min. TA volume level), it will be set to the last level.
When TA mode is on, TA of individual segment is turned on. When a TP station is received, TP of individual
segment is turned on. TA interruption function
The current traffic announcement is cancelled by pressing this key.
But the TA mode will not be off.
Broadcast station name data expressed in alphanumerically characters
AF: Alternative Frequencies
Frequency list of broadcasting stations transmitting the same program
TP: Traffic Program Identification
Identification data for traffic information-broadcasting station
TA: Traffic Announcement Identification
Identification data showing traffic information is being transmitted or not
OPERATION
5

Publicidad

Tabla de contenido
loading

Tabla de contenido