Optional Accessory; Overload Clutch - DeWalt D25733 Manual De Instrucciones

English
D WALT Tool Tag Ready (Fig. A)
e

Optional Accessory

Your hammer comes with mounting holes
fasteners for installing a D WALT Tool Tag. You will need a
e
T15 bit tip to install the tag. Only use the screws provided.
The D WALT Tool Tag is designed for tracking and locating
e
professional power tools, equipment, and machines using
the D WALT Tool Connect™ app. For proper installation
e
and use of the D WALT Tool Tag refer to the D
e
Tag manual.
Lock-On Button (Fig. A)
Chipping mode only
The lock-on button 8 offers increased comfort in extended
use applications. To lock the tool on, depress the lock-on
button while the tool is running. The tool will continue to
run after the switch is released. To unlock and turn off the
tool, depress and release the switch.
nOTE: The lock-on button will not function in drilling mode.
Electronic Speed and Impact Control (Fig. A)
The electronic speed and impact control allows the
use of smaller drill bits without the risk of bit breakage,
hammerdrilling into light and brittle materials without
shattering and optimal tool control for precise chiseling.
To set the speed dial , turn the dial to the desired level.
9
The higher the number, the greater the speed and impact
energy. Dial settings make the tool extremely flexible and
adaptable for many different appli cations. The required
setting depends on the bit size and hardness of material
being drilled.

Overload Clutch

In case of jamming of a drill bit, the drive to the drill spindle
is interrupted by the overload clutch. Due to the resulting
forces, always hold the tool with both hands and take a
firm stance. After the overload, release and depress the
trigger to re-engage drive.

WARNING: Drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill
firmly to control the twisting action and avoid injury.
E-Clutch® System (Fig. A)
In addition to the integral (mechanical) clutch, the D
anti-rotation E-Clutch® system, offers technology capable
of detecting the motion of the tool. This feature senses the
motion of the tool and shuts it down if necessary. The red
indicator LED illuminates when the E-Clutch® System
10
is engaged.
E-Clutch® and Service Indicator LEDs
(Fig. A)
Your rotary hammer has two LEDs
E-Clutch® (ADC) function and a service indicator. Refer to
the table for more information on LED functionality.
6
11 and
WALT Tool
e
WALT
e
10 , indicating the
lED Function Description
Red lock-on/service
(flashing)
The red indicator LED
up if the lock-on button
in any mode except the chipping
mode or if there is a fault with
the tool or the brushes have
completely worn out
Red E-Clutch®
(permanently on)
E- Clutch® is engaged.
Yellow Brush service
(permanently on)
The yellow brushwear indicator
LED
carbon brushes are nearly worn
out, indicating that the tool needs
servicing within the next 8 hours
of use.
Operation Modes (Fig. E)

WARNING: Do not select the operating mode when
the tool is running.

CAUTION: Never use in Rotary Drilling or Rotary
Hammering mode with a chisel bit in the bit holder.
Personal injury and damage to the the tool may result.
Your tool is equipped with a mode selector dial
select the mode appropriate to desired operation.
symbol Mode
Rotary
hammering
hammering
only
Bit Adjustment
To select an operating mode
• Rotate the mode selector dial
arrow points to the symbol corresponding for the
desired mode.
Fig. E
4
nOTE: The arrow on the mode selector dial
be pointing at a mode symbol at all times. It may be
necessary to briefly run the motor after having changed
10 lights
is used
8
10 lights up when the
4 to
Application
Drilling into concrete
and masonry
Light chipping
Chisel bit position
adjustment
so that the
4
must
4