nuair Avanty Manual Del Usuario página 13

CHARGING USING THE MAINS ADAPTOR
Caution!
1) Please use the attached charger to recharge the
dedicated, non-standard products will shorten the life
of the battery.
2) Charge your power station battery before using for the
first time.
3) After using, push the voltage test switch (7), check the
battery voltage (8): if the indicator is near the red zone,
it means that the battery must be recharged.
4) Recharge the power station battery after every
occasion of use if possible. And thereafter, at least
every 3 months.
5) Always avoid leaving your power station in a state of
discharge.
How to charge:
1) Plug the charger into 230V AC power outlet.
2) Plug the connector into the socket located on the rear
side of the Power Station, inside the air compressor
compartment (12). The charging indicator LED lights
at this time (10) become "red", means the ongoing
charge.
3) According to the use of battery, charging time is 6 ~ 40
hours.
4) After charging, LED indicator (10) turn to "green".
5) Disconnect the charger.
− During charging, it is possible to detect if the charge
has been completed. If the voltage meter (8)
remains in the green zone, over than 14V, it means
that the battery is close to the full charge.
− In order to achieve maximum battery life, it is
recommended to use often your power station, so
that the capacity of the battery is protected and its
expectancy life will be extended.
CHARGING USING THE 12V DC POWER SOURCE
1) Open one of the two covers of cigarette lighter socket,
on the front of the unit (1);
2) Plug the jack plug into the charging socket.
Note:
− Two cigarette lighter can work together for the
maximum power 200W.
− It is possible to use the double 12V socket for
charging. This in an auxiliary way to recharge the
Power Station, therefore its battery can not be
completely full recharged. Use the normal way of
recharging as much as possible.
USING THE "BOOSTER" FUNCTION
Warning!
Check the vehicle's battery voltages are 12V,
otherwise the battery could explode.
Please strictly follow the following steps, otherwise,
might pose a risk:
1) Turn the vehicle ignition and subsidiary equipment off.
2) Take great care not to touch the red positive(+) clamp
against the black negative (−) clamp.
3) Ensure the area is well ventilated.
4) Connect the red positive (+) clamp to the battery
positive (+) terminal first. Take care the clamp does not
contact any moving parts of fuel lines.
5) Connect the black negative (−) clamp to a suitable
earth point on the vehicle chassis.
6) If there is a wrong connection between positive and
negative poles, the Power Station emits an audible
alarm and the LED diode (green light) present on the
front, is turned on (5), by indicating the reverse polarity.
Please adjust and restore the positive and negative
proper polarity.
7) Set the switch (18) ON and start the car, be careful to
do not power the battery more than 5 seconds.
8) If the engine does not start properly, wait at least 3
minutes before restarting.
9) After the success of the engine to start, disconnect the
black(−) clamp. Then disconnect the red (+)clamp.
10) After use, always recharge the unit's battery fully.
USING THE AIR COMPRESSOR
Caution!
The working time of the pump can not exceed 10
minutes. After 10 minutes of operation, please
wait 10 minutes in order to allow the pump cooling
down. If the gauge goes up during the inflating
work, check the permeability of gas.
Inflatable operating steps:
1) Open the rear housing (12), in order to take the inflation
hose.
2) Select the inflation nozzle, according to the object/tire
to inflate (for car tire or bike tire, no additional nozzles
are required). Press the tip of the clip to lock securely.
3) Turn on the Air Compressor on/off switch (3), then it
start working; The air pressure will be indicated by the
compressed air pressure gauge (2) adjacent to the
switch.
4) Once the desired pressure is reached, turn off the Air
Compressor on/off switch (3).
5) When you have to inflate objects other than tires, use
one of the three inflation nozzles (needle for balloon,
nozzle for air mattress, fitting for bicycle tires). Read
the instructions for inflating your air object, before using
the inflator of this Power Station.
13
GB