Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
MODEL: PL31
Such precautionary measures reduce the risk
of injury to persons.
LOADING
TOOL
●
Do not load the tool with fasteners when
any one of the operating controls is
activated.
●
Never place a hand or any part of body in
fastener discharge area of tool.
●
Never point the tool at anyone.
●
Do not pull the trigger or depress the
workpiece contact as accidental
actuation may occur, possibly causing
injury.
!
WARNING:
The warnings and precautions
discussed above cannot cover all
possible conditions and situations that
may occur. It must be understood by
the user that common sense and
caution are factors which cannot be
built into this product, but must be
supplied by the user.
UNPACKING
●
This tool has been shipped completely
assembled.
●
Carefully remove the tool and any
accessories from the box.
●
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
●
Do not discard the packing material until
you have carefully inspected and
satisfactorily operated the tool.
●
If any parts are damaged or missing,
please call 1-888-669-5672.
!
WARNING:
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result
in possible serious personal injury.
!
WARNING:
Do not attempt to modify this tool or
create accessories not recommended
for use with this tool. Any such
alteration or modification is misuse
and could result in hazardous
condition leading to possible serious
personal injury.
06
HTTP://WWW.FREEMANTOOLS.COM
FEATURES
SPECIFICATIONS
AIR CONSUMPTION: 5.87 SCFM with 100
fasteners per minute @ 90 psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY:
18Ga. Brad nail: 100pcs
18Ga. Staple: 100pcs
16Ga. Finish nail: 80pcs
WEIGHT: 2.90 lbs
MAXIMUM PRESSURE: 110 psi
PRESSURE RANGE: 60 psi – 110 psi
FASTENER LENGTH RANGE:
18ga. brad nails: from 5/8" to 2"
18ga. staples: from 5/8" to 1-5/8"
16ga. finish nails: from 3/4" to 2"
0.079"(2mm)
0.118"(3mm)
1/4"(5.7mm)
5/8"
15mm
3/4"
20mm
3/4"
20mm
1"
25mm
1"
25mm
5/8"
16mm
1-1/4"
32mm
1-1/4"
32mm
3/4"
19mm
1-3/8"
35mm
1-3/8"
35mm
1"
25mm
1-1/2"
38mm
1-1/2"
38mm
1-1/4"
32mm
1-5/8"
40mm
1-5/8"
40mm
1-3/4"
45mm
1-1/2"
38mm
1-3/4"
45mm
1-5/8"
40mm
2"
50mm
2"
50mm
1.26 x 1.05mm
1.6 x 1.4mm
1.26 x 1.05mm
(0.063" x 0.055")
(0.050" x 0.041")
(0.050" x 0.041")
Calibre 18
Calibre 16
Calibre 18
Compatible with generic brands of 18 gauge
brad nails/staples and 16 gauge straight finish
nails.
FEATURES
●
360 ADJUSTABLE EXHAUST
°
Allows user to direct air away from
face.
●
COMFORT-GRIP HANDLE
For increased comfort and control.
●
ERGONOMICALLY ENGINEERED BODY
Rugged and Comfortable resulting in a
light-weight tool great for extended use.
●
ADJUSTABLE DEPTH
Depth is easily adjustable for various
applications.
●
NON-MARRING SAFETY CONTACT
Eliminate damage to working surface.
1-888-669-5672
MODEL: PL31
OPERATION
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool
allows users to direct the exhaust according to
operator preference. To adjust the direction,
turn the exhaust cap in the desired direction.
LOADING FASTENERS
1.
Connect the tool to the air source.
2.
Push down on the latch button(B). Pull back
on the magazine cover(C).
3.
For brad nail: Insert a stick of fasteners into
the magazine rail(D).
4.
For finish nail: Insert a stick of fasteners into
the magazine rail(I). Make sure the pointed
ends of the fasteners are resting on the
bottom ledge of the magazine when
loading.
5.
For staples: set a stick of fasteners on the
top of magazine.
6.
Make sure the fasteners are not dirty or
damaged.
7.
Push the magazine cover(C) forward until
latch button pops up.
Latch button
(B)
Magazine
cover(C)
NOTE:
This brad nailer/stapler can drive 16 Ga. straight
finish nails , 18 Ga. brad nails and staples. The
various type of fasteners are loaded in different
ways.
HTTP://WWW.FREEMANTOOLS.COM
18 Ga. brad nails :
Insert the nails into the LEFT-SIDE of the
magazine.
Magazine Rail(D)
18 Ga. Brad Nails
16 Ga. straight finish nails:
Insert the nails into the RIGHT-SIDE of the
magazine.
Magazine Rail(I)
16 Ga. Finish Nails
18 Ga. staples:
Load staples from the top of the magazine.
Staples
(18 Ga.)
!
WARNING:
The tool may fire when it is first
connected to the air source. Always
connect the tool to the air source
before loading fasteners to prevent
injury from unintended cycling. Always
make sure the tool's magazine is
empty at the beginning of each work
session, before connecting to an air
source.
1-888-669-5672
07
Publicidad
Tabla de contenido
Solución de problemas
