Protecting The Environment; Technical Data - Black and Decker BDCDS18 Manual De Instrucciones

ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting sanding mesh (Fig. E)
Hold the tool with the sanding base facing upwards.
u
Place the sanding mesh (7) onto the sanding base, mak-
u
ing sure that the holes in the sheet line up with the holes
in the base.
Fitting sanding sheets (Fig. F - Optional accessory)
Detach the two additional diamond-shaped tips (9) from
u
the sanding sheet (8).
The diamond-shaped tip (9) can be reversed and replaced
when worn.
When the front part of the tip (9) is worn, detach it from the
u
sheet, reverse it and press it onto the sanding base again.
When the whole tip is worn, remove it from the sanding
u
base and fit a new tip.
For optimal dust collection, ensure the correct type of sanding
paper is used.
Finger attachment (Fig. G)
The finger attachment is used for fine detail sanding.
Remove the screw (11).
u
Remove the diamond-shaped tip (10) from the sanding
u
base.
Fit the finger attachment (4) onto the sanding base.
u
Fit and tighten the screw (11).
u
Fit the appropriate sanding sheet onto the finger attach-
u
ment.
Replacing diamomnd shaped tip (Fig. G1)
Replace the diamond shaped tip (10).
u
Replace and tighten screw (11).
u
Fitting and removing the dust cassette (Fig. H)
Slide the dust cassette (2) onto the connector (2a) and
u
make sure that it is securely located.
To remove the dust casette, pull it to the rear and away
u
from the rear end of the tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
To switch the tool on, depress the on/off switch (1) at the
u
forward position I.
To switch the tool off, depress the on/off switch (1) at the
u
back position O.
8
(Original instructions)
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool or remove the battery pack.
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.

Protecting the environment

Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com

Technical data

Input voltage
Oscillations (no load)
Orbits (no load)
Sanding base surface
Weight
Battery
Voltage
Capacity
Type
Charger
Input voltage
Output voltage
Current
L (sound pressure) 68.2 dB(A), Uncertainty (K) 3 dB(A)
pA
L (sound power) 79.2 dB(A), Uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (main handle) (a
Vibration emission value (aux. handle) (a
BDCDS18
V 18
dc
min 12000
-1
min 12000
-1
mm 8866
2
kg 0.85
BL1518
V 18
DC
Ah 1.5
SSC-250040X
V 230
AC
V 8 - 20
DC
mA 400
2 2
) 5.98m/s , uncertainty (K) 1.5 m/s
h
2 2
) 7.3m/s , uncertainty (K) 1.5 m/s
h
1