Installation And Lubrication; Parts And Maintenance - Ingersoll Rand A Serie Especificaciones Del Producto

EN
Retainer Type
Model
Required
1A2S Yes
1A2SA, 1A2SA-EU Yes
2A2S Yes
2A2SA, 2A2SA-EU Yes
3A2S Yes
3A2SA, 3A2SA-EU Yes
4A2S Yes
4A2SA, 4A2SA-EU Yes
W1A1, W1A1-EU Yes
W2A1, W2A1-EU Yes
W3A1, W3A1-EU Yes
W4A1, W4A1-EU Yes
W1A2, W1A2-EU Yes
W2A2, W2A2-EU Yes
W3A2, W3A2-EU Yes
W4A2, W4A2-EU Yes
† K = 3dB measurement uncertanity
pA
‡ K = 3dB measurement uncertanity
wA
*K = Vibration measurement uncertanity

Installation and Lubrication

Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping,
air fi lter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose cou-
pling without internal shut-off , to prevent hose whipping if a hose fails or coupling disconnects. See drawing 16576183 and table on
page 2. Maintenance frequencies are shown in circular arrows and are defi ned as h=hours, d=days, and m=months. Items identifi ed as:
1. Air fi lter
2. Regulator
3. Lubricator
4. Emergency shut-off valve
5. Hose diameter
Note: Before storing the tool or leaving idle exceeding 24 hours:
3
- Pour 3 cm of IR # 10 oil into air inlet and run tool for 5 seconds.
Note: If the action of the tool becomes sluggish:
3
- Pour 3 cm of cleaning solution into air inlet and run tool for 30 seconds.
- Immediately after fl ushing the tool, pour 3 cm

Parts and Maintenance

When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that
they can be recycled.
Original instructions are in English. Other languages are a translation of the original instructions.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest Ingersoll Rand Offi ce or Distributor.
EN-2
Shank
Supplied Size Inch Collar
No 0.680 Round Oval
Plain 0.680 Round Oval
No 0.680 Round Oval
Plain 0.680 Round Oval
No 0.680 Round Oval
Plain 0.680 Round Oval
No 0.680 Round Oval
Plain 0.680 Round Oval
Rubber
0.580 Hex Round
Buff ered
Rubber
0.580 Hex Round
Buff ered
Rubber
0.580 Hex Round
Buff ered
Rubber
0.580 Hex Round
Buff ered
Rubber
0.680 Round Round
Buff ered
Rubber
0.680 Round Round
Buff ered
Rubber
0.680 Round Round
Buff ered
Rubber
0.680 Round Round
Buff ered
6. Thread size
7. Coupling
8. Safety Air Fuse
9. Oil
10. Oil - before starting, into air inlet
3 of oil into air inlet and run tool for 30 seconds.
Stroke Sound Level dB (A)
Blows per
Length
Minute
Inch (mm) † Pressure (L
2,500 1 (25)
2,500 1 (25)
2,300 2 (51)
2,300 2 (51)
1,725 3 (76)
1,725 3 (76)
1,480 4 (102)
1,480 4 (102)
2,500 1 (25)
2,300 2 (51)
1,725 3 (76)
1,480 4 (102)
2,500 1 (25)
2,300 2 (51)
1,725 3 (76)
1,480 4 (102)
(ISO15744) (ISO28927) m/s
) ‡ Power (L ) Level
p w
109.9 120.9 18.1
109.9 120.9 18.1
109.8 120.8 18.0
109.8 120.8 18.0
112.2 123.2 17.7
112.2 123.2 17.7
112.9 123.9 18.9
112.9 123.9 18.9
109.9 120.9 17.5
109.8 120.8 17.3
112.2 123.2 13.7
112.9 123.9 18.5
109.9 120.9 17.5
109.8 120.8 17.3
112.2 123.2 13.7
112.9 123.9 18.5
16574162_ed3
Vibration
2
*K
5.4
5.4
5.4
5.4
5.3
5.3
6.2
6.2
5.8
5.7
4.5
5.9
5.8
5.7
4.5
5.9