Cutting Depth Adjustment - Worx WX623 Traducción De Las Instrucciones Originales

OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for planning of firmly
supported wooden materials, such as beams
and boards. It is also suitable for beveling
edges and rebating.
1. SAFETY ON/OFF SWITCH
The switch is locked off to prevent accidental
starting. Depress the lock off button (1) then
on/off switch (3) and release lock off button (1).
The machine is working now. To switch off just
release the on/off switch.(See Fig. A)

2. CUTTING DEPTH ADJUSTMENT

Smaller cutting depth of 0-3mm is best for
most surface planing or rebating. Rotate the
depth adjustment knob (13) to set the required
cutting depth on the scale, Scale graduation
= 0.1mm. The clockwise rotation increases
the planing depth; the anti-clockwise rotation
reduces the planing depth. (See Fig. B)
3. ADJUST DUST EXTRACTION TUBE
AND CHIP EJECTION
Dust extraction tube can be adjusted to the
right or left side by manually. Rotating one end
of the dust extraction tube(5) until it stops (See
Fig. C). The arrowhead on the dust extraction
tube indicates the dust extraction direction.
NOTE: Due to the size and material
of some wood shavings e.g. wet or
hard wood it is possible for the dust
extraction tube to become blocked.
Remove the plug from the mains power
supply, then using a wooden stick clear
the blocked dust extraction.
4. BASEPLATE STAND (See Fig. D)
Uplift the rear of the planer, the baseplate
stand (15) can make the machine to be set
down directly and protect the cutting blades
from any damage and the blades from
damaging the surface. When planing, the
stand will be pushed away by the end of the
wood. Always check the stand is free to move
on the base plate.
Planer
5. BLADE FITTING AND CHANGING
(See Fig. E, F, G)
WARNING: Remove power cord
from the socket before carrying out
any adjustments or changing blades.
The blade has two cutting edges, which can
be reversed .When replacing or reversing the
plane blades, the guide groove guarantees
constant height adjustment.
NOTE: Dull and worn blade cannot be
reground and must be replaced.
Remove the plug from the mains socket.
Using the spanner (4) provided loosen the
3 bolts approximately 1/2 rotation counter-
clockwise(See Fig. E).Holding the blade clamp
in position, using a piece of wood slides the
blade (16) out of the blade clamp to remove
the blade from the blade clamp(See Fig. F).
NOTE: There is no need to remove the
blade clamp as this can change the
factory settings for cutting blade height
control.
Before reinserting a new or reverse blade,
always clean both the blade and the blade
seat if dirty. Slide the blade into the blade
clamp in the correct orientation. Check the
blade is equal with the clamp. (See Fig. G)
When tightening the screws ensure the correct
tightening sequence(Left right middle). Before
starting, rotate by hand to check the roller is
free to rotate.
Rotate the blade head by a further 180
repeat the procedure disassembling the
second plane blade.
6. REPLACING A DRIVE BELT
WARNING: 1. Remove the plug from
the socket before carrying out any
adjustment, servicing or maintenance.
2. The cutting blades will be turning and
may cause injury.
Loosen screw and remove belt cover (6),
remove worn drive belt from large pulley (a)
and pinion (b) and clean them (See Fig. H).lace
the new drive belt on the top of pinion and
turning it manually, press it on the large pulley
(a).Make sure the drive belt runs exactly along
the length grooves of the pinion and the pulley.
NOTE: Place the belt cover (6) back on
top and tighten it with screw.
9
and
o
EN