Descargar Imprimir esta página

Troubleshooting - Cooper Lighting Solutions HALO ESF1A4MW Instrucciones

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATING YOUR FIXTURE
1. For wall mount, rotate the motion sensor ball up or
down to desired detection pattern (Fig. 2A). For eave
mount, extend the motion arm away from the
coverplate and adjust to desired detection pattern
(Fig. 2B).
2. Rotate TIME knob on bottom of the sensor to
"TEST" (Fig. 6).
3. Turn on the power to fixture. Allow fixture to warm
up approximately 50 seconds before testing. (Lights
will come on during warm-up period.)
4. Aim sensor head toward desired detection area,
maintaining a 5°–15° down angle to allow moisture
to drain.
5. Walk across the detection zone at the farthest
distance you wish your detector to detect motion.
6. Adjust sensitivity knob until you get desired results.
Lights will turn off 4 seconds after all
motion stops.
NOTE: For maximum range performance, allow fixture
to operate in any mode (with power to the unit) for at
least 48 hours.
7. To set the ON time, rotate knob arrow to point to the
desired time setting within the TIME range (up to 12
minutes) (Fig. 6).
SELECTING YOUR DESIRED FEATURE
Mode
Procedure
Test Mode: Mode is
Dial/Switch Position:
designed to test
Sensitivity knob- Any/ desired
the fixture normal
position
operation.
Time knob - Test
Power switch- ON
Dusk to Dawn
Dial/Switch Position:
Mode: Mode is
Sensitivity knob- Any/ desired
designed to overide
position
motion fixture to
Time knob - Any/ desired position
operate in D2D
Dim- Any/ desired position
mode for 6 hours
Power switch- Turn the power OFF
and then return to
and ON twice within 3 seconds
motion mode after
that
Auto Mode: Mode
Dial/Switch Position:
is designed for
Sensitivity knob- Any/ desired
fixture normal
position
operation
Time knob - Any/ desired position
Dim- Any/ desired position
Power switch- ON
5
A
6
7
Result
Lights should turn ON
with motion both day
and night.
Lights should turn OFF
after 4 seconds.
Lights will not turn on
immediately if it's not
dark. At dark light will
turn ON for 6 hours and
return to Auto mode
Fixture get activated at
Dusk. Upon detection of
motion, it will turn ON
for set time duration
2

TROUBLESHOOTING

Problem
Cause / Solution
Light does not
No power to the fixture.
come ON with
• Check if circuit breaker tripped.
motion at night.
• Confirm wall switch is ON.
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Adjust the sensitivity knob.
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring; reconnect if necessary using wire nuts
(E) provided.
Light comes ON
There is motion in the detection zone.
for no apparent
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
reason at night.
TEST FOR YOURSELF:
• Cover the sensor lens with cardboard to prevent sensor
from detecting motion. If the light stays off, something in the
detection zone is triggering the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
• Adjust the sensitivity knob.
• Reposition the sensor.
Light stays ON at
There is motion in the detection zone.
night and does
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
not turn OFF.
• Adjust the sensitivity knob.
• Reposition the sensor.
If there is no motion in the detection zone, unit is in "Dusk to Dawn
Setting" (override mode).
• Turn the light switch to the OFF position for 40 seconds, and
then turn back to the ON position. This will send the unit back
into the "Auto" mode.
Light
The light given from the unit's own lamp is affecting the
motion sensor.
continuously
• Re-aim the lamp.
blinks ON and
• Reposition motion sensor.
OFF at night.
Light is ON
The controls on the bottom of the motion sensor are in "TEST" mode.
during the day.
• Change dial setting (not "TEST" mode).
The motion detector is shadowed.
• Reposition motion sensor.
Cannot activate
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
Dusk to Dawn
• Re-aim the head.
Setting at night
• Relocate or reposition the unit away from the light.
(override mode).
Not enough time is allowed to enter the "Dusk to Dawn Setting."
• Turn power OFF and ON twice within 3 seconds.
There is more than one fixture on an indoor wall switch.
• If so, put them on separate switches.
1-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions warrants to customers that, for a period of one year from the date
of purchase, Cooper Lighting Solutions products will be free from defects in materials and
workmanship. The obligation of Cooper Lighting Solutions under this warranty is expressly
limited to the provision of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser's receipt or other proof of date of original purchase ac-
ceptable to Cooper Lighting Solutions . This is required before warranty performance shall be
rendered. This warranty does not apply to Cooper Lighting Solutions products that have been
altered or repaired that have been subjected to neglect, abuse, misuse or accident (including
shipping damages). This warranty does not apply to products not manufactured by Cooper
Lighting Solutions which have been supplied, installed, and/or used in conjunction with
Cooper Lighting Solutions products. Damage to the product caused by replacement bulbs or
corrosion or discoloration of brass components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL COOPER LIGHTING SOLUTIONS BE LIABLE FOR SPECIAL, INDIRECT, INCI-
DENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN
CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS;
NOR SHALL THE LIABILITY OF COOPER LIGHTING SOLUTIONS FOR ANY CLAIMS OR DAMAGE
ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY,
USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING SOLUTIONS PRODUCTS,

Publicidad

loading

Este manual también es adecuado para:

Halo esf2a4mwHalo esf1a4mbHalo esf2a4mb