Publicidad
Idiomas disponibles
Idiomas disponibles
local de instalação
Install your Dompel product in a level place with no grooves or splices, preventing
rocking and vibration. The location must be airy and it must not allow straight sun-
light and it must be away from sources of heat (stoves, ovens, etc.) and flammable
products. Do not install your product outdoors.
limpeza e manutenção
Do not use metal spatulas, brushes and cleaning agents such as alcohol, acetone, kerosene, gasoline, bleach, thinner,
solvents, varsol, vinegar or other chemicals or abrasives such as sand paper or steel brushes.
To easily clean it, use a solution of warm water with a neutral soap and then wipe dry carefully. If chemical products reach
the upholstery, clean as soon as possible, preventing the products from staining or drying the fabric. The plastic parts
cannot be washed with boiling water. Chromed metal components can be cleaned with a soft, dry flannel, and silicone-ba-
sedautomotivewaxcanbeusedtoincreaseglossanddurability, in this case perform the task following the wax manufacturer's
instructions. Perform periodic cleaning, accumulated dust affects the beauty of the product making it difficult to clean the
product.
INSTALLATION AND ASSEMBLY
Remove all volumes from inside the package and follow these steps:
1
2
4
Manually insert the
finishing (plastic)
cover (M) of the
backrest support of
the recline system
or fixed support (K).
6
8
important
Never drag the product, if necessary, ask other person's help to remove the product from the place. Do not place
containers with high temperature on your product, at the risk of damaging plastic parts or the upholstery.
Merely illustrative images.
Products may suffer changes in its components without prior warning. If any questions, contact Dompel.
ENGLISH
IMPORTANT: DO NOT REMOVE THE
BASE PROTECTION UNTIL THE END OF
THE PRODUCT ASSEMBLY, IN ORDER
TO PROTECT THE FINISHING (PAINT
OR CHROME) OF POSSIBLE FALLING
SCREWS OR TIGHTENING WRENCHES.
Assemble the hydraulic (F) on the base
(J) using the washer set (M10) and lower
fixing screw (M10 x 25-SX) (H). Tighten
using a spanner 17.
5
Position the handle
guide for assembling
on the seat (align
the hole with the
seat thread) and fix
the 02 screws
(M6 x 25-SX)
pre-fixed on the seat
(N) using a spanner
10.
Assemble the footrest (C)
on the bottom of the seat
(A). Fasten the 04 screws
(M6 x 35-SX) (O) pre-fixed
on the seat) (A) with a
spanner 10.
Fit the handle (G) to the hydraulic pump (F). Pay attention to
the correct assembly position described on the label attached
to the pump. Fasten it by tightening the side screws
(M8 x 8-SX INT-SC) using an Allen key (4 MM).
3
Assemble the base / hydraulic set (F)
on the recline system or fixed support
set (K), tighten using the washer set
(M10) and upper screw (M10 x 60-SX)
(I) using the spanner 17.
IMPORTANT: Check the screw
tightness firmly before proceeding
to the next assembly step.
Assemble the seat set (A) on the recline
system (K), fixing the 06 screws
(M6 x 30-SX) (L) pre-fixed on the seat
(A), with the spanner 10.
7
9
security
Avoid accidents. After
unpacking the product,
keep all the pack material
out of children's reach.
Assemble the backrest
(B) on the recline
system (K): place the
04 backrest screws
(M6 x 35-AB) pre-fixed
on the part (E). Finish
the tightening using a
4mm Allen key.
Attach the headrest
(D) to the backrest
support (B) manually.
Publicidad
