Before Starting The Equipment; Practical Tips; Replacing The Power Cable - NUTOOL MP900N Manual Del Usuario

Sound and vibration
Sound and vibration values were measured in accordance
with EN 60745.
LpA sound pressure level
LWA sound power level
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values determined in accordance with
EN 60745.
Vibration level a (main handle):
h
Vibration level a (auxiliary handle):
h
Important!
The vibration value changes according to the area of
application of the electric tool and may exceed the
specified value in exceptional circumstances.

5 BEFORE STARTING THE EqUIPMENT

Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical to
the mains data. Always pull the power plug before making
adjustments to the equipment.
5.1 Adjusting the chip depth (Fig. 4/Item 1)
You can adjust the chip depth in steps of 0.1 mm from 0 to 2
mm by turning the setting knob for the chip depth (1).
Turn the setting knob for the chip depth (1) in a clockwise
direction to set a greater chip depth. Greater chip depth.
Turn the setting knob for the chip depth (1) in a counter-
clockwise direction to set a lower chip depth.
Lower chip depth
After finishing work, set the chip depth so that the
knives are lowered and thus protected from damage.
Turn the setting knob for the chip depth to position
"0" for this purpose.
5.2 Sawdust extraction (Fig. 5-6)
For an optimal sawdust extraction you can connect the
supplied dust bag (2) to the hand-held electric plane. To
do so, slide the dust bag (2) into the the chip ejector (7)
of the hand-held electric plane. The dust bag (2) can be
connected to the chip ejector (7) optionally on either the left
or right. Use the changeover switch (9) to select between
the chip ejectors (7).
5.3 Parallel stop (Fig. 7/Item 13)
Use the parallel stop (13) when you want to plane parallel to
the edge of the workpiece.
Fitting the parallel stop (Fig. 7)
• Fasten the mount (d) of the parallel stop to the left side of
the tool using the supplied thumb screw (a).
• Now connect the mount (d) to the slide of the parallel stop (13).
• The guide rail must always be aligned in downward direction.
• Fix the distance required between the parallel stop and
the edge of the workpiece.
• Fasten the parts with the carriage bolt (b) and the wing nut (c).
MP750N MP900N
L PA 87,5 dB(A) L PA 91,2 dB(A)
L WA 98,5 dB(A) L WA 102,2 dB(A)
MP750N MP900N
1,9 m/s 4,130 m/s
2 2
2,7 m/s - - -
2
15
6 OPERATION
6.1 ON/OFF switch (Fig. 8)
• The hand-held electric plane comes with a safety switch
which is designed to prevent accidents.
• To switch on the tool press the side safety lockoff (3) and
press the button switch.
• Release the button switch (4) to switch off the electric plane.
The button switch (4) jumps back into its starting position.

6.2 Practical tips

Important!
Only ever bring the hand-held electric plane towards
the workpiece while switched on.
6.2.1 Planing surfaces
Now adjust the desired chip depth. Equip the front base
plate and place the hand-held electric plane onto the piece
of wood you whish to plane. Then switch on the plane. Push
to electric plane over the surface with both hands and make
sure that the both the front and the rear base plate lie flat
on the workpiece.
Used a low chip depth for finishing surfaces and complete
several passes over the surface.
6.2.2 Chamfering edges (Fig. 9-10)
There is a V-shaped groove (a) in the front base plate that
enables you to plane edges at an angle of 45° for a smooth
finish.
Switch on the tool and wait until it reaches full speed. Place
the V-shaped groove (a) on the edge of the workpiece at an
angle of 45°. Now move the electric plane along the edge
of the workpiece.
To achieve a good quality result you should keep the feed
speed and angle constant.
6.2.3 Planing steps (Fig. 7/11)
The planing of steps is possible with the help of the parallel
stop (13).
Mount the parallel stop (13) on the left side of the tool (see
section 5.3).
To mount the depth stop fasten the step depth scale (12)
to the front right side of the plane housing with the locking
screw (11) (see Fig. 11).
Release the locking screw (11) and position the step depth
scale (12) so that the required step depth is displayed.
Tighten the locking screw (11) again.
Width of step:
You can set the width of the step with the parallel stop (13).
Depth of step:
We recommend you to set a cutting depth of 2 mm and to
keep planing the workpiece until the required depth of step
is reached.

7 REPLACING THE POWER CABLE

If the power cable for this equipment is damaged, it must
be replaced by the manufacturer or its aftersales service or
similarly trained personnel to avoid danger.
GB