Touchscreen Calibration - LRP Pulsar Touch Competition 41556 Manual Del Usuario

página de 7

/ 7
Marcadores

CONFIG

In „Config" the Pulsar Touch can be customised to your likes (adj. finish sound, °C or °F, etc), reset the charger to our factory

default setting plus it also allows you to calibrate the voltage readings of output jacket and balancer for maximum precision.

All chargers come of course calibrated from the factory, but due to aging of

components this calibration can slightly change over time.

P1 PROFILE NAME

Additionally the „Calibration" may be a useful tool at races when LiPo voltage

limit is checked and you can therefore adjust your charger to the multimeter

used in technical inspection in the best way.

CONFIG

SETUP

CONFIG

[1/2] X

Button Sound :

Finish Sound :15sec

Finish Melody:

LCD Contrast :

℃

Temp Scale

SET

CONFIG

[2/2] X

*Factory Reset

*Calibrate Output

*Calibrate Balancer

SET

Calibration process:

1. connect a battery to Pulsar Touch.

2. enter „Calibration Mode".

3. connect a separate voltmeter to the con-

nection you would like to calibrate.

4. compare reading in dispay with reading

on your voltmeter.

5. adjust voltage on display using up/down

arrow keys.

6. done when voltmeter + charger indicate

the same value. The press „ok".

TROUBLESHOOTING

The Pulsar Touch is protected against faults and operator errors by the Multi-Protection-System. Faults/Errors are displayed on the LCD screen and they

interrupt the active process to protect the unit and the battery.

Error Messages:

1. input voltage too low (<11.0V)

[ERROR]

or too high (>15.0V)?

INPUT

2. powersupplies current to low

for selected charge current?

Input Failure

3. contact/wiring problem?

must be 11-15V

1. no battery connected?

[ERROR]

2. bad contact on output?

OUTPUT

3. defective battery?

No conection

1. wrong battery connection!

[ERROR]

OUTPUT

Battery connected

with wrong polarity

1. contact/wiring problem?

[ERROR]

2. defective battery?

OUTPUT

Short Circuit

1. contact/wiring problem?

[ERROR]

2. defective battery?

OUTPUT

Loss of

connection

1. wrong setting for battery you

[ERROR]

connected?

OUTPUT

Voltage to high

1. wrong setting for battery you

[ERROR]

connected?

OUTPUT

2. contact/wiring problem?

3. defective battery?

Voltage to low

1.charger to hot, let charger cool

[ERROR]

down!

INTERNAL

Temperature

Overload

15A Fuse:

If the display is dark at power-up, you should check

for correct wiring first and then should also check the input fuse

input fuse for protection, only replace with another

15A fuse (blue coloured housing) and no other types

as these would not offer protection or correct function!

„On" or „Off"

„Off", „5sec", „15sec"

1-5 (different melodies)

depending on light condition, contrast may be altered.

„°C" or „°F"

Reset's your profile settings and profile names to our factory

defaults, please see section „Factory Defaults" for values.

FACTORY DEFAULTS

FACTORY defaults

Are you sure you

INITIALIZATION...

want to Reset?

________

CALIBRATE OUTPUT

Voltage

Calibrate voltage at output

0.000V

jacket.

CALIBRATE BALANCER X

Calibrate voltage of each cells

1s 0.000V

balancer.

2s 0.000V

3s 0.000V

4s 0.000V

[ERROR]

BALANCER

Cells connected

to different

[ERROR]

BALANCER

Cell Voltage

to high

[ERROR]

BALANCER

Cell Voltage

to low

[ERROR]

BATTERY

Temperature

to low

[ERROR]

BATTERY

Temperature

to high

[ERROR]

SENSOR

Temperature Sen-

sor disconnected

[ERROR]

INTERNAL

Calibration

Data damaged

TOUCHSCREEN CALIBRATION

If you should ever recognise a big difference between the LCD display and your actual touch point, you may need to re-

calibrate the positioning of the touchscreen!

How to re-calibrate the touchscreen:

< Touch Screen >

< CALIBRATION

Min=0000, 0000

Max=0000, 0000

USEFUL ACCESSORIES

LRP offers a comprehensive line of accessories, as well as particular spare- and optional items. Here you find an overview,

for a full picture please visit our website at www.lrp.cc:

#43200

Powersupply Competition 13.8V / 20A

#65821

Charge Wire Harness, LiPo 2S Hardcase

#65822

Charge Wire Harness, LiPo 2S Saddle Hardcase

#65835

4.0mm Silver plated connectors (10pcs)

#65848

LRP LiPo Safe Bag (large)

#81907

3.3mm² Powerwire black (1.0m)

#81908

3.3mm² Powerwire blue (1.0m)

Important: always follow the battery manufacturers recommendations first, our own recommen-

dation should only be seen as a guideline for the most common battery packs!

Battery

Type

LiPo 2S * 40-50C * 1/10 * ~7000mAh

LiPo 1S * 40-50C * 1/12 * ~5200mAh

LiPo 2S * Low C * TX Pack * 2500mAh

LiPo 3S * Low C * TX Pack * ~2500mAh

LiFe 2S * 30-50C * 1/10 * ~4500mAh

LiPo 2S * Low C * RX-Pack * ~2000mAh

LiFe 2S * Low C * RX-Pack * ~1500mAh

LiPo 2S * 20-35C * 1/10 Sub-C size

1. discharge level of cells within

pack to different?

LiPo 3S * 20-35C * 1/10 Sub-C size

2. bad contact at balancer?

NiMH 1/10 Sportpack (2000-3800mAh)

3. defective battery?

NiMH 1/10 Sportpack (>3800mAh)

NiMH AA/Mignon TX-Pack (~2500mAh)

NiMH RX Pack (~1500mAh)

For any other pack, make sure you select correct settings („Chg Mode" and „Pack Volt") and

1. wrong setting for battery you

charge with 1C* charge rate.

connected?

Leave the settings „Cut Temp" (40°C for LiPo/LiFePo and 55°C for NiMH) and „Safety Timer"

untouched.

* C=Nominal capacity of the battery. E.g. with a nominal capacity of 4000mAh (4.0Ah), the battery can be

charged with a max. current of 4.0A at 1C.

1. wrong setting for battery you

connected?

2. contact/wiring problem?

3. defective battery?

All products from LRP electronic GmbH (hereinafter called "LRP") are manufactured according to

the highest quality standards. LRP guarantees this product to be free from defects in materials or

workmanship for 90 days (non-european countris only) from the original date of purchase verified

by sales receipt. This limited warranty doesn't cover defects, which are a result of misuse, impro-

per maintenance, outside interference or mechanical damage.

Caution: only if optional tempe-

This applies among other things on:

rature sensor is connected!

• Cut off/changed original input- and/or output-wires

• Mechanical damage of the case, electronic components or PCB

1. battery to cold?

• Humidity/Water inside the case

2. contact/wiring problem?

• Soldered on the PCB"

• Charger disassembly by customer

• Any modification of the charger done by the customer

• Over temperature failures due to blocking the fan or the cooling slots

• Reverse polarity at DC output

Caution: only if optional tempe-

To eliminate all other possibilities or improper handling, first check all other components in your

rature sensor is connected!

model and the trouble shooting guide, if available, before you send in this product for repair. If

1. battery to warm?

products are sent in for repair, which do operate perfectly, we have to charge a service fee ac-

2. contact/wiring problem?

cording to our pricelist.

With sending in this product, the customer has to advise LRP if the product should be repaired

in either case. If there is neither a warranty nor guarantee claim, the inspection of the product

and the repairs, if necessary, in either case will be charged with a fee at the customers expense

according to our price list. A proof of purchase including date of purchase needs to be included.

Caution: only if optional tempe-

Otherwise, no warranty can be granted. For quick repair- and return service, add your address and

rature sensor is connected!

detailed description of the malfunction.

If LRP no longer manufactures a returned defective product and we are unable to service it, we

1. contact/wiring problem?

shall provide you with a product that has at least the same value from one of the successor

2. sensor defective?

series.

The specifications like weight, size and others should be seen as guide values. Due to ongoing

technical improvements, which are done in the interest of the product, LRP does not take any

responsibility for the accuracy of these specs.

Internal error, re-start your char-

ger and if needed reset to factory

LRP-Distributor-Service:

defaults and calibrate output/

• check www.LRP.cc

balancer again

1. with no power connected to the charger, keep the touchscreen pressed and

then connect the power to the charger.

2. keep the screen pressed, the charger will beep to indicate the charger is con-

nected to power first and if you keep the screen pressed it will make short

beeps. At this time, detach your hand from the screen.

3. an arrow will now be displayed in the upper left corner, precisely press the end

point of the arrow for 2sec.

4. an arrow will now be displayed in the lower right corner, precisely press the

end point of the arrow for 2sec.

5. the new touchscreen calibration is stored and you are done.

< Touch Screen >

< CALIBRATION

Min=0000, 0000

Max=0000, 0000

RECOMMENDED CHARGE CURRENTS

Chg

Mode

LiPo

LiFe

LiPo

LiFe

LiPo

Linear

REPAIR PROCEDURES / LIMITED WARRANTY

The crossed-out wheeled bin means that within the European Union the product

must be taken to seperate collection at the product end-of-life. Do not dispose of

these products as unsorted municipal waste.

[ CHARGER RESET ]

Please wait...

Pack

Current DPeak Trickle

Volt

7.4V / 2S

12.0A

3.7V / 1S

8.0A

7.4V / 2S

2.5A

11.1V / 3S

2.5A

6.6V / 2S

8.0A

7.4V / 2S

2.0A

6.6V / 2S

1.5A

7.4V / 2S

5.0A

11.1V / 2S

5.0A

4.0A

20mV

Off

5.0A

20mV

Off

1.0A

30mV

Off

1.5A

15mV

Off