Publicidad
Idiomas disponibles
Idiomas disponibles
2.0
SAFETY INSTRUCTIONS
CAUTION: The equipment contains electrical components under voltage. The equipment may be opened
only by an electrician of appropriate technical qualification. There is a danger of electrical accident!!
(a) The equipment is not intended for use by persons having reduced physical, sensory or mental ability (including children) without being supervised and
instructed by a responsible adult, for use by persons not well acquainted with the operation of the equipment within the scope hereof, persons whose
ability of immediate response is reduced due to consumption of drugs and/or narcotics, etc.
(b) The heat pump shall be located in compliance with the ČSN 33 2000-7-702 standard, i.e. at least 3.5 m from the outer edge of the pool.
(c) The feeding circuit of the heat pump shall meet the requirements of the applicable standard ČSN 33 2000 and shall be provided with the circuit breaker of
the minimum breaking current of 30 mA.
(d) Any intervention into the heat pump electrical installation and the power supply circuit shall be carried out only by an electrician of appropriate technical qualification.
(e) Do not install the heat pump in any place, where it can be flooded with water.
(f) Make sure that no children will be present within the heat pump working area. The main switch of heat pump shall not be placed within children's reach.
(g) Do not leave any incomplete heat pump in operation. All its protecting covers shall be always installed! The rotating blower may cause a serious body
injury. If in operation, the inner piping is hot and may cause burns.
(h) If it is found that the extension cable or supply cable of the pump is damaged, immediately switch the power supply circuit breaker OFF and have the defect made right.
(i) Any repairs of the heat pump and intervention in its pressure circuit of coolant shall be performed only by a duly qualified specialist.
(j) Maintenance and operation of this equipment shall be carried out in due compliance with these Instructions and their recommended frequency and periods shall be observed.
(k) Only original spare parts shall be used. Any failure to observe these recommendations may cause the guarantee provided with this product shall become
void and any claims will be refused accordingly.
3.0
EQUIPMENT DESCRIPTION AND TECHNICAL SPECIFICATION
3.1
TECHNICAL DATA
TYPE
Power supply
Power supply
dsd(V~ / Hz)
(V~ / Hz)
Protection degree
Protection degree
Protection class
Protection class
Heating capacity*
(kW)
Heating capacity*
(kW)
Cooling capacity*
Cooling capacity*
(kW)
(kW)
Rated power input*
(kW)
Rated power input*
(kW)
Operational power input*
Rated current *
(kW)
(A)
COP (heating, operational)*
Rated current *
(A)
Required water flow rate (min)
COP (heating, operational)*
(m
3
/h)
Required water flow rate (min)
Air flow rate
(m
(m
/h)
/h)
3
³
Air flow rate
Noise level
(dB(A))
(m
³
/h)
Cooling gas charge weight (R32)
Noise level
(dB(A))
(g)
Coolant (heat transfer fluid)
GWP
(-)
Cooling gas charge weight
Equipment weight
(kg)
(g)
Dimensions (L x D x H)
Equipment weight
(cm)
(kg)
Dimensions (L x D x H)
(cm)
* These values may vary subject to climatic and operating conditions.
3.2
POOL WATER PARAMETERS
The heat pump is designed for heating pool water that meets the requirements for its harmlessness in terms of bathing. The limit values for heat pump
operation: pH within the range of 6,8 – 7,9, chlorine total content shall not exceed 3 mg per litre. Water hardness shall be kept at the lower limit of its
optimum range, i.e. slightly above 8 °dGh.
4
BP-85HS-A
BP-100HS-A
BP-120HS-A
230 / 50
230 / 50
230 / 50
230 / 50
230 / 50
230 / 50
IP X4
IP X4
IP X4
IP X4
IP X4
IP X4
I
I
I
I
I
I
8,65
10,6
12
8,5
10,5
12
6,8
6,2
7,8
7,4
8,3
8,4
1,55
1,8
2,0
1,7
2,05
2,35
7,3
1,6
8,3
1,9
2,25
9,5
5,6
5,9
6,0
7,9
9,0
11,0
5,0
5,0
6,0
5,1
5,3
7,0
2000
4,0
2400
4,5
2800
6,0
2000
<50
2400
<52
<52
2800
<52
650
<53
750
<54
820
R 410A
675
R 410A
675
R 410A
675
950
45
1100
54
1300
57
85 x 29 x 54
52
91 x 31 x 62
61
90 x 31 x 67
63
93 x 28 x 55
101 x 31 x 61
101 x 31 x 66
3.3
HEAT PUMP DIMENSIONS
BP-85HS-A
A
A
B
B
C
C
BP-140HS-A
D
D
230 / 50
230 / 50
E
E
IP X4
IP X4
F
F
I
I
G
G
14
14
H
H
9,6
9,7
2,4
2,7
Note: The dimensions are given in mm.
11,0
2,6
WARNING: The manufacturer reserves the right to make such product modifications that will not influence its essential properties.
5,8
12,5
5,4
8,0
3.4
DESCRIPTION OF BASIC PARTS
3200
7,0
3200
<53
<55
930
R 410A
675
1500
62
96 x 33 x 72
68
107 x 34 x 70
1
2
BP-100HS-A
BP-120HS-A
295
296
340
340
490
580
555
665
286
285
305
305
320
320
370
370
846
935
1010
900
290
300
300
330
90
91
101
100
539
540
614
615
3
4
6
5
8
7
BP-140HS-A
342
340
365
366
555
663
615
723
306
305
330
331
370
370
395
395
1010
900
1070
960
363
385
385
400
103
101
101
103
664
665
715
715
1 – Blower protective grille
(air outlet))
2 – Housing
3 – Upper lid
4 – Control panel
5 – Pressure gauge
6 – Neck for water outlet pipe connection
7 – Neck for water inlet pipe connection
8 – Power supply cable
5
Publicidad
Capítulos
