Publicidad
Idiomas disponibles
Idiomas disponibles
! ! ! ! !
Do not touch the PCB for at least 2 minutes
after removing the power supply: 250 V_
may still be present across the PCB circuitry
of this device.
! ! ! ! !
This device is designed to work with Nickel-
Cadmium batteries. When disposing of used
batteries, abide by the Local laws in force.
! ! ! ! !
The self-powered versions (Wave/WSB and
Wave/WB) must be powered for at least 24
hours to ensure that the battery is fully
charged.
General Features
ˆ Available with or without back-up battery, with
or without Strobe
ˆ 2 selectable sound types
ˆ Tamper detection (tamper and snatch tamper)
ˆ Universal Wall mount bracket
General Description
The Wave HornStrobe is an Audible-Visual Alarm
signalling device for Security Systems.
It is available in four versions, as per the follow-
ing table.
9HUVLRQ
:DYH:6%
:DYH:%
:DYH:6
:DYH:
All versions have piezoelectric transducers for audi-
ble signalling, whereas only the Wave/WSB and
Wave/WS versions are fitted with Strobes for visual
signalling.
The Wave/WSB and Wave/WB versions are fit-
ted with 7.2 V – 300 mA batteries (art. CB7203)
for back-up power during blackout.
All versions have tamper terminals that signal the
removal of the Lid and the snatch.
Installation Guidelines
Carefully work through the following steps (see Fig-
ure 1).
This HornStrobe is suitable for indoor use only.
1. Remove the Logo Insert 5.
2. Remove the screw 4.
3. Pull the Lid 3 upwards and away from the
backplate.
6WUREH
%D.NXS %DWWHU\
<(6
<(6
QR
<(6
<(6
QR
QR
QR
G ENGLISH
G
G
G
G
4. Remove the Lens cover 2.
_
_
_
_
5. Using a screwdriver or similar tool, push down
on the locking tab 9 and push the Wall bracket
12 away from the Backplate 10.
6. Pull the connection wires through the cable
entry 13.
7. Using anchor screws, secure the Wall bracket
12 to the wall or to the outlet box.
Snatch Tamper functions ONLY when a
screw is properly fixed in the hole 14 (fi-
gure.1).
! ! ! ! !
Be careful to avoid conduits and plumb-
ing when drilling.
8. Pull the connection wires through the cable en-
try 11.
9. Slide the Backplate 10 downwards onto the
Wall bracket 12 until it snaps closed.
10. Select the required sound type, as per the
instructions in the relevant section.
11. Complete the connections on the terminal
board 7, as per the instructions in the rel-
evant section.
12. Replace the Lens cover 2.
13. For Wave/WSB and Wave/WB only: locate
the battery 6, as per Figure 1, then connect it
to the input J5.
! ! ! ! !
For Wave/WSB and Wave/WB only: before
connecting the battery, ensure that: the Posi-
tive Voltage (13.8 V) is on terminal +B; the
Positive Voltage (13.8 V) is on terminal +N
or jumper J3 is connected; Ground is
present on –A.
14. Snap the top of the Lid 3 onto the Backplate
10, then push the bottom part onto the
backplate posts.
15. Replace the Closure screw 4.
16. Replace the Logo Insert 5.
Selecting the Sound type
Two different sounds are selectable via jumper J15:
-
6281' 7<3(
8S DQG 'RZQ V.DOH PRGXODWLRQ 'HIDXOW
%LWRQH
Publicidad
