Battery; Battery Charger; Accessories; Installation Information - GGMgastro BSW2200 Manual De Instrucciones

6 BRUSH UNIT STEEL PLATE
7 ADJUSTABLE SPLASH GUARD
8 FRONT RIGHT BUMPER WHEEL
9 MACHINE RIGHT WHEEL
10 FLOOR CLEANER ADJUSTABLE RIGHT WHEEL
11 FLOOR CLEANER FRONT FLAP
B PHOTO B
12 CONTROL PANEL
13 HAND GRIP
14 FORWARD/REVERSE GEAR LEVER
15 FLOOR CLEANER UP/DOWN LEVER
16 BATTERY CHARGER CONNECTOR
17 PARKING BRAKE LEVER
18 DIRTY WATER TANK INSPECTION WINDOW
19 BRUSH UNIT UP/DOWN PEDAL
20 FLOOR CLEANER RIGHT BUMPER WHEEL
21 FLOOR CLEANER LEFT BUMPER WHEEL
22 SUCTION TUBE
23 DIRTY WATER TANK DRAINAGE PIPE
24 SOLUTION DOSING LEVER
C PHOTO C
25 FORWARD/REVERSE GEAR LUMINOUS INDICATOR
26 LUMINOUS INDICATOR OF MAXIMUM SPEED SET
27 REDUCE SPEED SWITCH
28 INCREASE SPEED SWITCH
29 BRUSH MOTOR ON LUMINOUS INDICATOR
30 BRUSH MOTOR SWITCH
31 SUCTION MOTOR ON LUMINOUS INDICATOR
32 SUCTION MOTOR SWITCH
33 BATTERY CHARGER STATUS LUMINOUS INDICATOR
34 BRUSH MOTOR THERMAL CUTOUT
35 DRIVE MOTOR THERMAL CUTOUT
36 IGNITION KEY
D PHOTO D
37 FLOOR CLEANER RIGHT WHEEL ADJUSTING KNOB
38 FLOOR CLEANER SUPPORTING BODY
39 FLOOR CLEANER SLANT ADJUSTING KNOB
40 FLOOR CLEANER RIGHT FIXING PIN
41 FLOOR CLEANER BODY
42 FLOOR CLEANER FLAP FIXING BRACKET
43 FLOOR CLEANER REAR FLAP
44 FLOOR CLEANER FOIL FIXING SCREWS
45 FLOOR CLEANER LEFT FIXING PIN
46 FLOOR CLEANER LEFT WHEEL ADJUSTING KNOB
47 SOLUTION TANK DRAINAGE PLUG
48 LEFT REAR CUSHIONED WHEEL
49 RIGHT REAR CUSHIONED WHEEL
E PHOTO E
50 SUCTION MOTOR COVER
51 SUCTION MOTOR COMPARTMENT
52 BATTERIES -ACCORDING TO SPECIFICATIONS-
53 BATTERY CONNECTION CABLES -ACCORDING
TO SPECIFICATIONS-
54 SUCTION MOTOR IMPERMEABLE SPONGE FILTER
F PHOTO F
55 BRUSH MOTOR SPEED REDUCER
56 SOLUTION DISPENSING TUBE
57 TRANSVERSAL AXIS RIGHT ADJUSTING ECCENTRIC
58 LONGITUDINAL AXIS RIGHT ADJUSTING ECCENTRIC
G PHOTO G
59 TRANSVERSAL AXIS LEFT ADJUSTING
ECCENTRIC
60 BRUSH
61 BRUSH MOTOR

5.2.2 BATTERY

If supplied, the Pb-Acid (if not dry charged) or gel
batteries are ready to be installed:
Positive pole - red
Negative pole - black

5.2.3 BATTERY CHARGER

If supplied, refer to the corresponding booklet.

5.3 ACCESSORIES

Your machine supplier can provide a complete and
updated list of all available accessories, such as brushes,
scrapers, disks, etc.

6. INSTALLATION INFORMATION

6.1 BATTERY PREPARATION

The technical features of the batteries used must
match those indicated in the technical features section.
Using different batteries may cause serious damage to
the machine or may require them to be charged more
frequently.
During installation or when performing any type of
battery maintenance, the operator must be equipped
with adequate safety accessories to prevent accidents.
Work far from open flames, do not short-circuit the
battery poles, do not generate sparks and do not smoke.
The batteries are normally supplied full of acid solution
(for the Pb-Acid type) and ready for use. In any case,
follow the steps indicated in the manual supplied with
the battery and carefully follow the instructions regarding
safety and operating procedures.
6.2 BATTERY INSTALLATION AND PREPARATION
These operations must be carried out by specialised
personnel.
Disconnect the Anderson connector of the battery wiring
from the Anderson connector of the machine wiring.
Always hold the connectors with the hands and never
pull on the cables.
Attach the battery wiring to the battery, connecting
the terminals only on the poles marked with the
same symbol (red wiring "+", black wiring "-")! A
battery short-circuit may cause an explosion!
(PHOTO E)
After checking that all the controls on the panel (PHOTO
C) are in position "0" or at rest, connect the battery
connector to the machine connector.
Close the battery compartment making sure not to
crush any wires.

6.3 BATTERY CHARGER STATUS INDICATOR

CONFIGURATION ACCORDING TO THE TYPE USED
(PB-ACID OR GEL)
TO ENTER THE BATTERY THRESHOLD
CONFIGURATION MODE:
1) Press simultaneously keys "REDUCE SPEED" and
29