Asist AR06-1001FL Traducción De Instrucciones Originales De Uso página 28

by twisting the darkening regulator 9 on the outside
of the helmet.
ATTENTION! The darkening regulator 9 has the se-
tting position "grind". If the darkening regulator 9 is set
to this position the automatic darkening is deactivated.
Only use this setting when you do not wish to use the
welding helmet for welding. The automatic darkening
is then no longer active.
Check the light density before each use.
Test procedure: Bring the viewing panel closer to an
external light source with a value of more than 40 W
and examine whether or not the screen darkens or
illuminates. To do so, turn the darkening control 9 cloc-
kwise from „grind" to the next position. This sets the
filter to auto-darkening mode. If you turn the darkening
control 9 anticlockwise back to „grind", the filter's auto-
-darkening feature is once again deactivated.
You can adjust the delay setting 11 to configure whe-
ther or not the autodarkening feature should be swit-
ched off immediately after stopping welding work,
depending on the type of welding work. At the lowest
setting, auto-darkening is switched off immediately.
Turn the rotary switch clockwise towards the highest
setting to prolong the time the auto-darkening feature
remains active after welding work. This feature is very
useful for handling afterglow.
You can use the sensitivity setting 12 to adjust the li-
ght sensitivity of the sensor. With low incident light, the
control can be adjusted to the highest setting to ensure
that the auto-darkening feature is activated even for
a weak light source. Even with this additional feature,
you can also adjust the light sensitivity of the sensor to
suit your own personal requirements.
Storage
Keep the device in a dry place and out of
the reach of children.
Cleaning and Maintenance
Do not use any harsh cleaning agents to clean the hel-
met casing 2 .
Never bring the UV filter into contact with water.
Clean the product with a soft, dry cloth, with a cloth
dampened with pure alcohol or with a cloth dampened
with disinfectant.
Error Cause
The filter
The protector
does not
does not
darken in
darken in a
a normal
normal way or
way or
flickers.
flickers.
The filter
does not
darken in The arc sensor is
a normal not clear.
way or
flickers.
The filter
does not
The welding
darken in
current is
a normal
too low.
way or
flickers.
Solution
Clean the protector
or
replace it.
Clean the arc
sensor's
surface.
Set the sensitivity
to the
maximum degree.
28
The The ambient
reaction is temperature is
slow. too low / high.
The
The sensitivity is
reaction is
too low.
slow.
The protector /
The visibility
the protective
is poor.
screen is dirty.
The protective
film on the
The visibility
protective screen
is poor.
was not
removed.
The ambient light
The visibility
is not
is poor.
sufficient.
The wrong
The visibility
darkening shade
is poor.
has been set.
The headband 5
The welding
has been
helmet slips.
put on incorrectly.
TECHNICAL DATA AR06-1001FL, AR06-1001LI
Material: polypropylene
Filter cassette size 110 x 90 x 9 mm
Visor size 92.5 x 42.5 mm
2x dimmer sensor
grinding function
Powered by solar + lithium battery
Permanent UV protection DIN 16
Adjustable darkness range of the DIN 9-13 filter
Automatic filter darkening time max. 0.0003 s Setting
the backlight delay 0.1 - 0.8 s
sběrných střediscích určených ke sběru a likvidaci
elektronářadí. Takto odevzdané elektronářadí bude
shromážděno, rozebráno a dodáno k opětovnému
zhodnocení nepoškozujícímu životní prostředí.
Subject to changes.
ENVIRONMENTAL PROTECTIONWASTE MANAgE-
MENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and its approximation
in national laws, unfit power tools must be handed
over at the point of purchase of similar equipment, or
Only use the
welding helmet in
temperatures
between -5 °C and
+55 °C.
Set the sensitivity
to a
higher setting.
Clean the protector
and the
protective screen.
Remove the
protective film.
Apply more light
to your
work surroundings.
Reset the
darkening shade.
Put on the
headband 5
again tighter.