Felisatti SRF305/1800 Instrucciones De Servicio página 12

Removing or Installing the Right Side Sliding
Fence (Fig. 19)
1. Unlock the fence cam-locking lever, and slide the
sliding fence to the right.
2. Remove the hex screw (3) by a using a 3 mm hex
key.
3. Lift up on the sliding fence to remove it from the
saw.
4. Replace the sliding fence and thread the hex screw
to lock the sliding fence when not making right bevel cuts.
Compound Cut (Fig. 20)
1. Extending the fence by sliding it out to the required
location or remove the right sliding fence if necessary.
2. Set the desired bevel angle using the bevel lock
handle (2).
3. Set the desired mitre angle and lock into position.
See "MITRE CUT".
Base Moulding Cut (Fig. 21)
1. Base moulding can be cut vertical against fence or
flat on the table. Follow the table below for reference.
SETTINGS Vertical Position
(Back of moulding is
against the fence)
Extension Fence Close to the blade
Bevel Angle
Moulding Position Left side
Inside Mitre Left at
Corner Angle 45°
Moulding Bottom
position against
table
Finished Keep left
side side of
cut
Outside Mitre Right at
Corner Angle 45°
Moulding Bottom
position against
table
Finished Keep left
side side of
cut
Crown Moulding Cut (Fig. 22)
1. Crown moulding can only be cut flat on the table for
this mitre saw.
2. This mitre saw has special mitre stops of 31.6°
left and right and a bevel stop of 33.9° for a special crown
moulding, i.e. 52° between the back of the moulding and
the top flat surface that fits against the ceiling; 38° between
the back of the moulding and the bottom flat surface that
fits against the wall. Refer to the following table for this
crown moulding cut.
SETTINGS
Inside Corner
Mitre Angle
Bevel Angle
Moulding
Position
Finished Side
12
Horizontal Position
(Back of moulding is
flat on the table)
Far from the blade
0° 45°
Right Left side Right
side side
Right at 0° 0°
45°
Bottom Top Bottom
against against against
fence fence fence
Keep Keep left Keep left
right side
side of side of
of cut cut cut
Left at 0° 0°
45°
Bottom Bottom Top
against against against
table table fence
Keep Keep Keep
right side right side right side
of cut of cut of cut
Left Side Right Side
31.6° Right 31.6° Left
33.9° 33.9°
top against bottom against
fence fence
Keep left Keep left
side of cut side of cut
Outside Corner
Mitre Angle
Bevel Angle
Moulding
Position
Finished Side
NOTE:
1. These special stops can not be used with 45° crown
moulding.
2. Since most rooms do not have angles of exactly
90°, fine tune is needed and always take a test cut to
confirm the correct angles.
Pullover Cut (Fig. 23)
WARNING!
- Never pull the cutting head assembly and spinning
blade toward you during the cut. The blade may try to climb
up on the top of the workpiece, causing the cutting head
assembly and spinning blade to kick back.
- Never lower spinning saw blade down before pulling
the cutting head to the front of the saw.
1. Unlock the carriage lock handle (1) and allow the
cutting head assembly to move freely.
2. Set both the desired bevel angle and/or the mitre
angle and lock into position.
3. If bevel cutting, set both the left and right sliding
fences (2) to their proper location.
4. Use a hold down clamp to secure the workpiece.
5. Grasp the saw handle (3) and pull the carriage (4)
forward until the centre of the saw blade is over the front of
the workpiece (5).
6. Pull the trigger (6) to turn the saw on.
7. When the saw reaches full speed, push the saw
handle down, slowly, cutting through the leading edge of
the workpiece.
8. Slowly move the saw handle toward the fence,
completing the cut.
9. Release the trigger and allow the blade to stop
spinning before allowing the cutting head to raise.
Setting Cutting Depth (Fig. 24)
The depth of cut can be preset for even and repetitive
shallow cuts.
1. Adjust the cutting head down until the teeth of the
blade are at the desired depth of cut.
2. While holding the upper arm in position, turn the
stop knob (1) until it touches the stop plate (2).
3. Recheck the blade depth by moving the cutting
head front to back through the full motion of a typical cut
along the control arm.
The Arbour Laser Guide
Your tool is equipped with our latest innovation, the
Arbour Laser Guide, a battery powered device using
Class 1M laser beams. The laser beams will enable you
to preview the mitre blade path on the workpiece to be cut
before you begin your operation.
DANGER! Laser is activated when blade is rotating.
Do not stare into beam or view directly with optical
instruments. Do not remove the warning label affixed
to the blade guard. Avoid direct eye contact with light
source.
NOTE: The red laser line will appear as a dotted line
when the motor is activated and the blade assembly is in
the uppermost position. This broken line will assist you in
aligning the mark on your workpiece with the cutting path
of the saw blade. As you lower the blade assembly, the
31.6° Left 31.6° Right
33.9° 33.9°
bottom against top against
fence fence
Keep right side Keep right side
of cut of cut