Manuales relacionados para Sauder W003213142
Resumen de contenidos para Sauder W003213142
- Página 1 Dinette Table NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24...
- Página 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identification Assembly Steps 5-18 Rubber Mallet Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2...
-
Página 3: Part Identification
Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT FRONT/LEFT REAR TOP (2) TOP CENTER BRACE (1) - Página 4 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. HIDDEN CAM - 14 CAM DOWEL - 14 10F TWIST-LOCK FASTENER - 8 WOOD DOWEL - 28 CAM COVER - 4 GLUE - 1 SCREW COVER - 36 BLACK 1-7/8"...
- Página 5 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER Push a TWIST-LOCK FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Página 6 Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Some assembly å (and snacks) required. To begin assembly, push eight TWIST-LO CK FASTENERS (10F) into the large holes in the TOP SHORT BRACES (G).
- Página 7 Step 2 å Fasten the TOP SHORT BRACES (G) to the TOPS (A). Tighten eight TWIST-LOCK FASTENERS. Surface with TWIST-LOCK FASTENERS There should be a small gap between the TOPS (A). Surface without TWIST-LOCK FASTENERS Page 7...
- Página 8 Step 3 å Push two HIDDEN CAMS (1F) into the TOP CENTER BRACE (H). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. å Fasten the TOP CENTER BRACE (H) to the TOPS (A). Tighten two HIDDEN CAMS.
- Página 9 Step 4 å Push eight HIDDEN CAMS (1F) into the TOP LONG BRACES (F). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow Metal end Page 9...
- Página 10 Step 5 å Fasten the TOP LONG BRACES (F) to the TOPS (A). Tighten eight HIDDEN CAMS. å Fasten the TOP LONG BRACES (F) to the TOP SHORT BRACES (G). Use four SILVER 2" FLAT HEAD SCREWS (57S). å Fasten the TOP LONG BRACES (F) to the TOP CENTER BRACE (H).
- Página 11 Step 6 å Push a HIDDEN CAM (1F) into each of the OUTER LEG PANELS (D). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow Metal end (4 used) Page 11...
- Página 12 Step 7 å Slide the notched edges of the LEG PANELS (E and K) into the grooves in the OUTER LEG PANELS (D). Now might be a good time to refresh å NOTE: The finished surfaces on the LEG PANELS (E and K) your drink.
- Página 13 Step 8 å Fasten a LONG LEG PANEL (B) to each of the RIGHT FRONT/LEFT REAR LEG PANELS (E) and LEFT FRONT/ RIGHT REAR LEG PANELS (K). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). BLACK 1-7/8" FLAT HEAD SCREW (16 used in this step) Page 13...
- Página 14 Step 9 å First, fill the holes in the LONG LEG PANELS (B) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the holes in the TOP SHORT BRACE (G) 1/4 to 1/2 full with GLUE.
- Página 15 Step 10 å First, fill the holes in the LOWER SHORT BRACES (I) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the holes in the LOWER LONG BRACE (J) 1/4 to 1/2 full with GLUE.
- Página 16 Step 11 å First, fill the holes in the LOWER SHORT BRACES (I) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the holes in the LONG LEG PANELS (B) 1/4 to 1/2 full with GLUE.
- Página 17 Step 12 å First, fill the holes in the SHORT LEG PANELS (C) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the holes in the LOWER SHORT BRACES (I) 1/4 to 1/2 full with GLUE. Then, insert the WOOD DOWELS in the SHORT LEG PANELS into these holes.
- Página 18 Step 13 å Carefully stand your unit upright. Pro Tip: Lift with your å Center a SCREW COVER (18P) over the head of each SCREW and legs. And, you know, gently tap in with your hammer. your arms. å Using your hammer, gently tap a CAM COVER (13P) onto each visible HIDDEN CAM.
-
Página 19: Liste De Pièces
Table-dînette Utilisez les instructions d’ a ssemblage en français avec les NOUS CONTACTER EN PREMIER schémas étape par étape du manuel d’instruction en anglais. AVANT D'EFFECTUER TOUT RETOUR AU MAGASIN. Chaque étape en français correspond à la même étape en Nous faisons de notre mieux pour nous assurer que votre meuble anglais. - Página 20 Guide d'utilisation de la visserie ÉTAPE 3 UTILISATION DE LA FIXATION TWIST-LOCK Enfoncer deux EXCENTRIQUES ESCAMOTABLES (1F) dans l’ENTRETOISE CENTRALE SUPÉRIEURE (H). Ensuite, insérer Enfoncer une FIXATION TWIST-LOCK dans le gros trou l'extrémité en métal de la CHEVILLE D'EXCENTRIQUE (2F) dans de la pièce.
- Página 21 ÉTAPE 7 ÉTAPE 11 Enfiler les chants crantés des PANNEAUX DE PIED (E et K) dans Attention: Examiner bien les pièces avant d'assembler. Il est les rainures des PANNEAUX DE PIED EXTERNES (D). difficile de séparer des pièces une fois encollées. REMARQUE : Les surfaces finies sur les PANNEAUX DE PIED (E et K) Tout d’...
-
Página 22: Mesita De Comedor
Mesita de comedor Use estas instrucciones de ensamblaje en español junto con las CONTÁCTENOS PRIMERO figuras paso-a-paso provistas en el folleto inglés. Cada paso en ANTES DE HACER DEVOLUCIONES A LA TIENDA. español corresponde al mismo paso en inglés. Compare la “Lista Tratamos de asegurar que su mueble llega en condición excelente. - Página 23 Guía de uso de herrajes PASO 3 CÓMO UTILIZAR EL SUJETADOR TWIST-LOCK Empuje dos EXCÉNTRICOS ESCONDIDOS (1F) en la RIOSTRA CENTRAL SUPERIOR (H). A continuación, inserte el extremo de Empuje un SUJETADOR TWIST-LOCK dentro del agujero metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada grande en la parte.
- Página 24 PASO 7 PASO 11 Deslice los bordes con muesca de los PANELES DE LA PATA (E y K) Precaución: Revise las partes cuidadosamente antes de dentro de las ranuras de los PANELES EXTERIORES DE LA PATA (D). ensamblar. La separación de las piezas ya pegadas es muy difícil. NOTA: Las superficies acabadas sobre los PANELES DE LA PATA (E y K) Primero, llene los agujeros de las RIOSTRAS CORTAS deben estar hacia afuera.
- Página 25 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Improperly moving furniture. •...
- Página 26 ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Mover los muebles incorrectamente. •...
-
Página 27: Garantie Limitée De 5 Ans
5-YEAR LIMITED WARRANTY 4. This Warranty applies only to warranted defects that first arise 1. We provide limited warranty coverage to the original purchaser of this product for a period of five and are reported to us within the warranty coverage period. The years from the date of purchase against defects in materials or workmanship of furniture components.