Technical Data; English - Berner BACPM BL 18V Manual Original

TECHNICAL DATA

Polisher
Code
Battery voltage
Rated speed
Polishing backing pad Diameter
Polishing pad Diameter max.
Thread of work spindle
Weight according EPTA-Procedure 01/2003 (Li-Ion 5,0 Ah)
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration total values (triaxial vector sum) determined according
to EN 60745.
Polishing:
Vibration emission value a
h,P
Uncertainty K
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
POLISHER SAFETY INSTRUCTIONS
Safety warnings that are common for polishing:
a) This power tool is intended to function as a polisher.
Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to
follow all instructions listed below may result in electric
shock, fi re and/or serious injury.
b) Operations as sanding, abrasive and rough grinding,
and working with wire brushes are not recommended to
be performed with this power tool. Operations for which
the power tool was not designed may create a hazard and
cause personal injury.
c) Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can break
and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by
fl anges, the arbour hole of the accessory must fi t the
locating diameter of the fl ange. Accessories that do not
match the mounting hardware of the power tool will run out
of balance, vibrate excessively and may cause loss of
control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for

ENGLISH

457 088 - Berner-BACPM BL 18V.indd 20 457 088 - Berner-BACPM BL 18V.indd 20
BACPM BL 18V
BACPM BL 18V 01 00001-99999
18 V
360-2200 min
-1
125 mm
180 mm
M14
3,1 kg
78,54 dB(A)
89,54 dB(A)
1,1 m/s
2
1,5 m/s 2
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If
power tool or accessory is dropped, inspect for damage
or install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-load
speed for one minute. Damaged accessories will normally
break apart during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments. The eye
protection must be capable of stopping fl ying debris
generated by various operations. The dust mask or
respirator must be capable of fi ltrating particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of workpiece
or of a broken accessory may fl y away and cause injury
beyond immediate area of operation.
j) Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cutting
accessory may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric
shock.
k) Position the cord clear of the spinning accessory. If
you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
20
18.07.2017 14:07:15 18.07.2017 14:07:15