Operation; Remote Mode; Manual Mode; System Status - Espa SilenPlus Manual De Instrucciones

If you do not have ControlSystem or prefer not to use it,
the system can work just as well manually. the system can work just as well manually.
Ignore the activation and calibration operations, switch ctivation and calibration operations, switch
to Manual mode and then connect the SilenPlus. to Manual mode and then connect the
4.5 Changing the ControlSystem
If it is necessary to replace the ControlSystem
system that is already linked, you will need to delete system that is already linked, you will need to delete
the old serial number before linking the new one. fore linking the new one.
To do this, with the SilenPlus pump connected to the
power supply, keep the F button pressed down for 10
seconds. Flashing LEDs indicate that the operation seconds. Flashing LEDs indicate that the operation
has been carried out correctly.
The previous serial number will be deleted and the The previous serial number will be deleted
system will go into "link standby" mode. Proceed as system will go into "link standby" mode. Proceed as
indicated in 4.2.2.

5. OPERATION

5.1 REMOTE mode

This is the default operating mode.
The pump carries out the most appropriate function The pump carries out the most appropriate function
considering the position of the filter valve. (See figure considering the position of the filter valve. (See figure
3)
In FILTRATION position: Filtration Plus
• In BACKWASH position: Backwash
• In CLOSED position: pump stopped.
In CLOSED position: pump stopped.
• In any of the other positions: the pump operates at
In any of the other positions: the pump operates at
100% power.
• When you operate the valve control, the pump
When you operate the valve control, the pump
stops automatically to make the valve movement ally to make the valve movement
easier.
• In any intermediate position, the pump remains
In any intermediate position, the pump remains
stopped.
To change the working mode, simply move the valve To change the working mode, simply move the valve
to the desired position.
To prevent accidental operation, the electronic To prevent accidental operation, the electronic
response is delayed by 1 second. The flashing response is delayed by 1 second. The
red LED indicates that proper communication red LED indicates that proper communication
has been achieved.
Move the valve gently.
WARNING: the valve configuration must correspond WARNING: the valve configuration must correspond
to the 6 standard positions, according to figure 3. to the 6 standard positions, according to figure 3.
For other valve configurations, contact your technical For other valve configurations, contact your technical
service.

5.2 MANUAL mode

When you press the M, key SilenPlus ignores the
trolSystem signal and runs one of the preset functions: signal and runs one of the preset functions:
The MAN LED comes on.
The pump starts up at a fixed, programmable speed. The pump starts up at a fixed, programmable speed.
The standard setting is 2,300 RPM (40 Hz). This is The standard setting is 2,300 RPM (40 Hz). This is
what is known as the MIXED CYCLE (MISC. CYCLE). is known as the MIXED CYCLE (MISC. CYCLE).
If you press the F key, it runs through the various key, it runs through the various
SilenPlus functions in sequence.
or prefer not to use it,
ControlSystem in a
pump connected to the
button pressed down for 10
Filtration Plus function
Backwash Plus function
ignores the Con-
Between each function, the pump stops to allow valve Between each function, the pump stops to allow valve
movement or other operations. movement or other operations.
The sequence is:
1. Mixed cycle (MISC. CYCLE). Mixed cycle (MISC. CYCLE).
2. Stop.
3. Filtration Plus.
4. Stop.
5. Backwash Plus.
6. Stop.
7. Mixed cycle...
The lit LEDs indicates the function selected at all The lit LEDs indicates the function selected at all
times.
When you press the M button again, you leave Ma
ual mode to go back to Remote. ual mode to go back to Remote.
5.3 No water fault and retries. 5.3 No water fault and retries.
In Filtration Plus mode, the system is regularly mon mode, the system is regularly moni-
tored to check that the pump is not operating without tored to check that the pump is not operating without
water.
If SilenPlus detects the pump is working without water detects the pump is working without water
it stops the motor.
The system will attempt to start up again after 1', 5', The system will attempt to start up again after 1', 5',
15' and 1 hour (Fig. 4). If the retries fail, Evopool will 15' and 1 hour (Fig. 4). If th
remain in permanent fault mode. remain in permanent fault mode.
An LED sequence indicates the fault status. (See fig- An LED sequence indicates the fault status. (See fi
ure 7)
To interrupt the retry cycle or to restart from perma- To interrupt the retry cycle or to restart from perm
nent fault mode, press the F

5.4 System status

Espa offers installers and us Espa offers installers and users the EspaEvopool ap-
plication for monitoring the system status and plication for monitoring the system status and
interacting with SilenPlus.
You need to have an Android device with Blu You need to have an Android device with Blue-
tooth connectivity and tooth connectivity and the EspaEvopool app
available from
With this app, it is possible to switch between app, it is possible to switch between Man-
ual/Remote modes and use all functions. modes and use all functions.
6. ADVANCED CONFIGURATION 6. ADVANCED CONFIGURATION
Different speeds can be set to adjust the functions to Different speeds can be set to adjust the functions to
the characteristics of the installation. the characteristics of the installation.
The function being run will be configured. The function being run will be configured.
To configure a function, first select it, either in Manual gure a function, first select it, either in Manual
or Remote mode, and at the same time press M + F or Remote mode, and at the same time press
for 5 seconds.
All the speeds of the selected function will return to All the speeds of the selected function will return to
the factory settings [= fs]
To increase or decrease the speed, press M or F: To increase or decrease the speed, press M or F:
M = + 58 RPM (+ 1 Hz)
F = - 58 RPM (- 1 Hz)
• Configuring Filtration Plus
Filtration Plus.
The filtration speed is set. The filtration speed is set.
· Minimum = 1,600 RPM (20 Hz), [= fs] · Minimum = 1,600 RPM (20 Hz), [= fs]
· Maximum = 2,900 RPM (50 Hz), [= fs] · Maximum = 2,900 RPM (50 Hz), [= fs]
10
button again, you leave Man-
F key.
www.espa.com www.espa.com
1 Hz)
1 Hz)
EN