Tabla de contenido
Publicidad
OBJ_BUCH-1845-002.book Page 15 Friday, June 14, 2013 12:48 PM
– Tighten screw 2 again.
– Mount auxiliary handle 5 to dust cover 6.
Mounting a Guide Roller (see figure B)
Mount guide roller 11 with the wing nuts 12 to the dust cover.
Mounting the Spindle Extension (see figure C)
– Press spindle lock 1 and mount spindle extension 10 using
an open-end spanner (size 21 mm).
– Insert feather key 7 into spindle extension 10.
Mounting Application Tools (see figure D)
– Press the spindle lock 1.
– Slide the application tool onto the spindle extension. En-
sure that the feather key 7 is tightly seated.
– Tighten locking screw 8.
Pay attention that the arrow directions on the application tool
and the housing of the power tool correspond.
Choice of Application Tool/Abrasive
Depending on the material to be worked and the required rate
of material removal, different application tools/abrasives are
available:
– Rollers with permanent abrasive
– Rollers for use with changeable sanding belts
– Deflection rollers for use with sanding belts
For dry sanding and pre-sanding coarse
For structuring and for smooth-
ing out minor unevenness
For satin-finishing and matt-
finishing of metal surfaces
Operation
Starting Operation
Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate
of the machine.
Switching On and Off
To start the machine, press the On/Off switch 4 and keep it
pressed.
To lock the pressed On/Off switch 4, push the On/Off switch
4 further toward the front.
To switch off the power tool, release the On/Off switch 4, or
when it is locked, briefly press the On/Off switch 4 and then
release it.
To save energy, only switch the power tool on when using it.
Preselecting the Speed
Operate with a speed adapted to the application, in or-
der to prevent damage to the material.
The required speed can be preselected with the thumbwheel
3 (also while running).
Bosch Power Tools
The required speed depends on the material and the working
conditions and can be determined through practical testing.
When using fleece, do not work with a higher setting
Working Advice
When sanding, the removal capacity and the surface quality
are mainly determined by the abrasive selection as well as
through the preselected speed.
Work with the lowest possible sanding pressure in order to in-
crease the service life of the abrasive. Excessively increasing
the sanding pressure does not lead to a higher sanding capac-
ity, but to more wear of the power tool and the abrasive.
Work with moderate feed and perform the sanding parallel
and overlapping with respect to the sanding paths.
To achieve a perfect surface, do not skip more than one grain
size when selecting the abrasive.
Use only original Bosch sanding accessories.
Only proper abrasives achieve good sanding capacity and
give the power tool longer service life.
Do not clamp power tools in the saw stand. Clamped
Storage of the Sanding Belts
Grain size
Store sanding belts in their original packaging at
40, 60
15 °C – 25 °C room temperature and 40 % – 70 % humidity.
80
Do not store sanding belts on concrete floors, close to open
medium
Combination-
windows or heaters.
fleece rollers
Do not bend or kink the sanding belts, otherwise they will be-
come unusable.
120 –240
fine
Fleece rollers
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
For safe and proper working, always keep the machine
Remove adherent sanding dust with a brush.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
than speed stage 4 (max.). Otherwise, the fleece will
become too hot.
power tools and sharp-edged application tools may result
in serious injury.
plug.
and ventilation slots clean.
English | 15
3 609 929 C51 | (14.6.13)
Publicidad
Tabla de contenido
