Important Safety Instructions; Important Safety Advice; Care And Maintenance - hylite ecoheater Instrucciones De Operación

English
ECO HEATER

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL AND OPERATE THIS
HEATER

IMPORTANT SAFETY ADVICE

WHILST MEETING THE REQUIREMENTS OF BS:EN90335-2-30, THE SURFACE OF THIS TUBULAR
HEATER CAN STILL GET HOT. IT IS THEREFORE RECOMMENDED THAT THE AGED, INFIRM,
CHILDREN AND ANIMALS ARE NOT LEFT UNSUPERVISED IN THE VICINITY OF THE HEATER UNLESS
A SUITABLE GUARD IS FITTED.
DUE TO THE HIGH SURFACE TEMPERATURES, IT IS ESSENTIAL THAT COMBUSTIBLE OR FLAMMABLE
OBJECTS SUCH AS FABRICS OR CLOTHING DO NOT COME INTO CONTACT WITH THE HEATER.
IF A TUBULAR HEATER IS TO BE INSTALLED IN A PLACE USED BY THE PUBLIC A WARNING NOTE
SHOULD BE PLACED ADJACENT TO THE HEATER ADVISING THAT THE SURFACE IS HOT.
ALWAYS ENSURE THE POWER CORD IS IN GOOD CONDITION AND PROPERLY CONNECTED TO THE
HEATER PRIOR TO OPERATION, IF THE CORD IS DAMAGED DISCONTINUE USING THE PRODUCT AND
CONTACT THE MANUFACTURER FOR FURTHER INSTRUCTIONS
ALWAYS SWITCH THE HEATER OFF AT THE MAINS WHEN NOT IN USE AND ENSURE THE POWER
CORD IS NOT IN CONTACT WITH THE SURFACE OF THE HEATER.
THE HEATER MUST ALWAYS BE POSITIONED HORIZONTALLY USING THE MOUNTING BRACKETS
SUPPLIED AND ALLOWING FREE MOVEMENT OF AIR AROUND THE HEATER. DO NOT COVER THE
HEATER AS THIS MAY CAUSE OVERHEATING.
THE HEATER HAS AN IP55 RATING FOR WATER RESISTANCE AND IS SUITABLE FOR USE IN LOFTS,
GARAGES, UTILITY ROOMS, CONSERVATORIES, GREENHOUSES, AIRING CUPBOARDS, SHEDS,
DISPLAY WINDOWS ETC. HOWEVER IT IS NOT WATERPROOF AND SHOULD NOT BE USED IN
ENVIRONMENTS WHERE CONTINUOUS OR EXCESSIVE WATER-SPRAYING MAY OCCUR.
DO NOT USE THE HEATER IN BATHROOMS, SHOWERS OR SWIMMING POOLS.
INSTALLING THE ECO HEATER
IMPORTANT : THE HEATER SHOULD ONLY BE INSTALLED AND
OPERATED IN THE HORIZONTAL PLANE, USING THE MOUNTING
BRACKETS PROVIDED. IT SHOULD BE MOUNTED TO A WALL AT
LOW-LEVEL AND NOT BELOW A SOCKET OUTLET
Follow minimum clearances below and above the heater as shown
in [Fig.1]
Any shelving placed above the heater must be at a distance of at
least 400mm
The fixing brackets should be mounted according to the heater
length and at a distance to adequately support the heater
Once a suitable location has been found, screw the two bottom
halves of the bracket to the wall [Fig.2]
Place the Eco Heater on the brackets and then fasten top part of the
brackets over tube to secure.
DO NOT SWITCH ON THE HEATER UNTIL IT IS SECURED
ELECTRICAL
IMPORTANT: THE ELECTRICAL INSTALLATION OF THIS ECO HEATER MUST BE CARRIED OUT BY A
COMPETENT ELECTRICIAN, IN ACCORDANCE WITH THE CURRENT IEE REGULATIONS FOR ELECTRICAL
EQUIPMENT IN BUILDINGS
The Eco Heater is suitable for operation on a 50Hz AC supply voltage as shown on the identity label.
Before connecting the heater check that the supply voltage is the same as that stated on the identity label.
The input wiring, if connected to fixed wiring, must have a fused double pole switch in the power circuit.
After switching on the appliance for the first time the element will emit a vapour for approximately two
minutes. This is no cause for alarm, but is merely preservative burning out from the element.
The unit is fitted with a safety device, which will automatically cut off the heat source should the unit
overheat. The heater will re-energise once the temperature has reduced to the desired level.
NOTE: THIS APPLIANCE MUST BE EARTHED.

CARE AND MAINTENANCE

Wiping over with a damp cloth and finishing with a soft dry cloth can maintain the finish of your Hylite Eco
Heater
Cleaning should only be carried out when the tube heater is cold and switched off
DO NOT use abrasive cleaning powders or metal polish on any part of the tube.
English
400mm min.
Fig.1
30mm min.
Fig.2