Fiap proficontrol Manual De Instrucciones página 3

FIAP proficontrol Steuerung
GB
Information about this operating manual
Please read the operating instructions and familiarise yourself with the unit prior to using it for the first
time. Adhere to the safety information for the correct and safe use of the unit. Please keep these
operating instructions in a safe place! Also hand over the operating instructions when passing the
unit on to a new owner. Ensure that all work with this unit is only carried out in accordance with these
instructions.
Intended Use
The series FIAP proficontrol Steuerung is used to control FIAP feeders in aquaculture. Use other than
that described above will damage the product, is also associated with risks, such as. Short circuit, fire,
electric shock, etc.. The product may not be modified or rebuilt!
The safety instructions must be followed!
Use other than that intended
Danger to persons can emanate from this unit if it is not used in accordance with the intended use and
in the case of misuse. If used for purposes other than that intended, our warranty and operating permit
will become null and void.
CE Manufacturer's Declaration
We declare conformity in the sense of the EC directive, EMC directive (2004/108/EC) as well as the
low voltage directive (2006/95/EC). The following harmonised standards apply:
EN 55014-1, EN 55014-2, EN 60335-1, EN 60335-2-41, EN 60598-1, EN 60598-2-18, EN 61000-3-2,
EN 61000-3-3, EN 61558-2-6
Safety information
The company FIAP has built this unit according to the state of the art and the valid safety regulations.
Despite the above, hazards for persons and assets can emanate from this unit if it is used in an
improper manner or not in accordance with its intended use, or if the safety instructions are ignored.
For safety reasons, children and young persons under 16 years of age as well as persons who
cannot recognise possible danger or who are not familiar with these operating instructions, are
not permitted to use the unit. Hazards encountered by the combination of water and electricity.
The combination of water and electricity can lead to death or severe injury from electrocution, if the unit
is incorrectly connected or misused. Prior to reaching into the water, always disconnect the power
supply to all units used in the water.
Correct electrical installation
Electrical installations at garden ponds must meet the international and national regulations valid for
installers. Especially adhere to DIN VDE 0100 and DIN VDE 0702. Only use cabes admitted for
external use and meeting DIN VDE 0620. Ensure that the transformer is protected by a rated fault
current of max. 30 mA via a fault current protection device. Only connect the transformer when the
electrical data of the power supply is identical to that on the type plate. Only operate the transformer
when plugged into a correctly fitted socket. For your own safety, consult a qualified electrician when
you have questions or encounter problems.
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
5
www.fiap.com
FIAP proficontrol Steuerung
Safe operation of the unit
Keep socket and power plug dry. Route the power cables so that damage is excluded. Do not carry or
pull the units by the connection cables. The power connection cables cannot be replaced. If the cable
is damaged, the entire unit has to be disposed of. Never open the unit or its attendant components,
unless this is explicitly mentioned in the operating instructions. Never carry out technical modifications
to the unit. Only use original spare parts and original accessories for the unit. Only have repairs carried
out by authorised customer service points.
Commissioning
The FIAP proficontrol Control can operate up to 4 feeders (FIAP Breeding Feeder, FIAP Electronic
Feeder). The control of the FIAP proficontrol Control, control feeders are automatically detected and
controlled accordingly, depending on engine type. The active channel is indicated by an LED channel.
The following FIAP feeders are possible:
FIAP Breeding Feeder
FIAP Electronic Feeder
FIAP Electronic Feeder with spreader
The buttons on the controller can FIAP proficontrol Control the running time in seconds (1 - 99).
Wait time in minutes (1 - 99) and the motor speed can be adjusted in 99 steps for each output.
The total FIAP proficontrol Control can be via a separate button on or off.
The settings are retained after a reset (power off) is obtained.
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
6
www.fiap.com