Description Of Symbols; General Safety Warnings - Silverline 598446 Manual De Instrucciones

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Caution!
Toxic fumes or gases!
Risk of fire!
Risk of explosion!
NO open flames!
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools must not be disposed of with household waste. Air
tools may contain traces of tool oil and other lubricants and so
must be recycled accordingly
Specification
Maximum operating pressure:..............8bar (116psi)
Working pressure: ................................3-5bar (45-75psi)
Air Inlet: ................................................¼" BSP, supplied
with two male airline quick connectors (EN-6 'UK' and
EQ-4 'European' types)
Spray gun body material: .....................Cast aluminium
Paint container material: ......................Aluminium
Paint container volume: ........................750cm3
Type of feed:.........................................Suction
Nozzle diameter: ..................................6mm
Min. hose diameters:
8mm (
5
9.5mm (
Air consumption: ..................................85-227L/min
Weight ..................................................1.0kg
As part of our ongoing product development, specifications
of Silverline products may alter without notice.
4
⁄ ") for supply hose length up to 15m
16
⁄ ") for longersupply hoses
3
8
(3-8cfm)

General Safety Warnings

• For multiple hazards, read and understand the safety instructions before
installing, operating, repairing, maintaining, changing accessories on, or
working near this tool. Failure to do so can result in serious bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of
safety measures and increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and
markings required by this part of ISO 11148 are legibly marked on
the tool. The employer/user should contact the manufacturer to obtain
replacement marking labels when necessary
WARNING: This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience
or knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the
appliance.
Projectile Hazards
• Be aware that failure of the workpiece or accessories, or even of the
inserted tool itself, can generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool.
The grade of protection required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed
Entanglement Hazards
• Choking, scalping and/or lacerations can occur if loose clothing, personal
jewellery, neck wear, hair or gloves are not kept away from the tool and
its accessories
Operating Hazards
• Use of the tool can expose the operator's hands to hazards, including
cuts, abrasions and heat
• Wear suitable gloves to protect hands
• Operators and maintenance personnel should be physically able to
handle the bulk, weight and power of the tool
• Hold the tool correctly; be ready to counteract normal or sudden
movements and have both hands available
• Maintain a balanced body position and secure footing
• Release the start-and-stop device in the case of an interruption of the
energy supply
• Use only lubricants recommended by the manufacturer
• Personal protective safety glasses should be used; suitable gloves and
protective clothing are recommended
• Avoid direct contact with moving parts in order to prevent pinching or
cutting of hands or other body parts. Wear suitable gloves to protect
hands
• Never run the tool unless it is directed towards the workpiece
• There is a risk of electrostatic discharge if used on plastic and other
non-conductive materials
• Potentially explosive atmospheres can be caused by aerosols and fumes
resulting from spraying
• Always use dust extraction or suppression systems which are suitable for
the material being processed
Repetitive Motions Hazards
• When using this tool to perform work-related activities, the operator can
experience discomfort in the hands, arms, shoulders, neck or other parts
of the body
• While using this tool, the operator should adopt a comfortable posture
whilst maintaining secure footing and avoiding awkward or off-balance
postures. The operator should change posture during extended tasks; this
can help avoid discomfort and fatigue