brennenstuhl SES P4033 Manual Del Usuario página 6

Solar Energy Set SES P4033
GB
How to use / Operation
Solar charge regulator
FRONT
Digital voltage meter
Over discharge indicator
USB
output
Inverter female CLA output
REAR
Connection to battery
Fuse
Please make sure that the connection to this charge regulator
is tight and secure.
The charge regulator needs to be turned on in order to activate
all its functions.
A digital voltage meter is included to show real time battery
voltage. A push button switch is available to turn on the digital
display only when needed, in order to save valuable electricity.
The charge regulator provides following protections to maintain
system's proper working condition:
A. Over-discharge protection: When the electricity level of
the battery goes too low (lower than 11±0.3 V), the solar
charge regulator will automatically shut off power output to
prevent the battery from over discharge. "Low vol"- indicator
on the front side of charge regulator will be on. The output to
appliance will resume when battery voltage increases back
to 12 V. Please disconnect the appliance, and charge the
battery until full.
B. Over-charge protection: When the electricity level of the
battery goes too high (higher than 14.0-14.5 V), the system
controller will automatically shut off power input to prevent
damage to the battery. The input from Solar module will
resume when battery voltage decreases to 13.5 V.
C. Over-load protection: When output power goes too big, the
fuse in the system controller will be melted to prevent dam-
age to the controller itself. Fuse has to be replaced in order
to bring the controller back to working condition in this case
(car fuse 10 A – red).
Connecting sockets:
Front side
DC output:
1 x 12 V cigarette lighter adapter socket: Can be used to
power appliances that have a cigarette lighter adapter,
2 x 12 V DC connector sockets (6,3 mm)
1 x 6 V DC connector socket (3,5 mm)
1 x 3 V DC connector socket (3,5 mm)
6
Switch for digital voltage meter
ON/OFF Switch
12V female CLA output
Connection to Solar Panel
Inverter
1x cigarette lighter adapter socket to connect the power
inverter:
This output draws power directly from rechargeable battery
and is not regulated by this solar charge regulator.
USB
1x USB output socket (5V DC): Can be used to charge elec-
tronic devices that get power from USB port (MP3 player,
mobile phone, ...).
Digital Voltmeter
Display
ON/OFF switch
Back side
Fuse
Connection terminal "BATTERY"
Connection terminal "SOLAR"
Power inverter
Use only for small AV appliances (230 V, max. 150 W)
Connect ¿ rstly the power inverter with the solar charge
regulator (inverter female CLA output).
Make sure that you do not connect to the 12 V female
CLA output. Danger of burning the built-in charge con-
troller if you do so.
Turn on ¿ rstly the power inverter as source, then the appli-
ance (consumer).
Caution:
When connecting an appliance with motor or compres-
sor to the power inverter, please make sure that the peak
power rating of the power inverter is approx. 3 times the
power rating of the electrical appliance, because the start-
ing up power is much higher than the power rating of the
appliance.
If the inverter makes a beeping sound: switch off your ap-
pliance, unplug the inverter and recharge the battery. (The
beeping sound is simply the low battery warning which
indicates that the voltage of battery is getting low).
If the battery is too low, the inverter will shut down auto-
matically.
The inverter will switch off automatically if the total wattage
of appliances exceeds the inverter's output capacity.
This will also happen if the temperature of the inverter
exceeds 60°C due to prolonged use.
On the rear panel is a terminal ¿ tted with a nut (CHASSIS
GND). The use of this terminal will depend on the particular
installation. In a vehicle, connect the chassis ground lug to
the chassis of the vehicle. In a boat, connect to the boat's
grounding system. In a ¿ xed location, connect to earth.
FRONT
USB socket
Power switch
REAR
AC output
socket