Sunbeam Mr. Coffee Manual De Instrucciones página 6

Grip clockwise until it stops, then pull out of unit. The top burr is attached
to the Removable Top Burr Grip. Use the brush included to clean the burr.
7. To install top burr, place into place and twist the Removable Top Burr
Grip counterclockwise until it stops. When twisting the Top Burr Grip into
place, you will hear clicks. Pull on the Removable Top Burr Grip to confirm
it is locked into place.
8. Install the Bean Hopper by aligning the arrow
the unlock symbol on the unit base and then twisting clockwise. The
arrow on the Bean Hopper should now be aligned with the lock symbol
on the unit base.
9. Place Chamber Lid back on Grind Chamber and then install into unit by
pushing to lock into place.
TROUBLESHOOTING YOUR MR. COFFEE
BURR GRINDER
Your MR. COFFEE® Burr Grinder has been carefully designed to give you
many years of trouble-free service. In the unlikely event that your new Burr
Grinder does not operate satisfactorily, please review the following potential
problems and try the steps recommended BEFORE you call an Authorized
Sunbeam Service Center.
Problem Possible Causes
THE UNIT DOES • Bean Hopper is not
NOT GRIND securely intact
• Grind Chamber is not in
position
• On/Off Button has not
been pressed
• Unit is unplugged
• There's a power outage
• Motor has overheated,
thermal fuse is open
• Hopper Chute Clogged (or
Blocked)
THE COFFEE • Grinder setting is incorrect
GROUNDS • Insufficient amount of
PRODUCED ARE whole beans in hopper
INSUFFICIENT • Grind chamber moved
out of position during
operation
• Top Burr Mill is not in
proper position
• Unit and Burr Mill are not
clean
• There is a foreign object
between the two Burr Mills
9.
BVMC-BMG25_20ESM1 (US).indd 9-10 BVMC-BMG25_20ESM1 (US).indd 9-10
on the Bean Hopper with
®
Solutions
• Turn hopper clockwise, so the
arrow on the hopper aligns with
the lock symbol on the unit
• Place Grind Chamber in proper
position
• Press and hold briefly start/stop
button
• Plug unit in
• Wait for power to be restored
• Unplug unit for at least an hour
then plug back in ans use as
needed
• Remove Bean Hopper and
empty to clear blockage by
removing upper burr, follow
instruction on page 8.
• Set grinder setting correctly
• Add beans to hopper
• Place chamber in proper
position
• Unplug unit, place top burr mill
in proper position
• Clean unit, unplug it and clean
burr mill
• Unplug unit and carefully
dislodge foreign object by
removing the upper burr, follow
cleaning instructions on page 8.
THE SIZE OF • Unit and Burr Mill are not
GROUND clean
COFFEE • There's a foreign object
PARTICLES IS NOT between the two Burr Mills
CONSISTENT • Grind setting is not correct
• The Removable Top Burr
Grip is not locked into
place
THE UNIT STOPS • Grind setting is incorrect
GRINDING • Grind Chamber is not in
correct position
• On/Off Button has been
pressed
• The unit has been
unplugged
• There's a power outage
• Grind Chamber is full and
is clogging the Burr Mill
compartment
• Motor has overheated,
thermal fuse is open
THE CUP • Timer is at 2 cup
SELECTION DIAL setting, cannot turn
DOES NOT TURN counterclockwise anymore
• Timer is at 18 cup setting,
cannot turn clockwise
anymore
• Cup selection dial is
broken
THE GRIND SIZE • Grind size selector is at the
SELECTOR DOES Fine Setting, cannot turn
NOT TURN clockwise anymore
Do you still have questions? You can call us toll-free at the MR. COFFEE®
Consumer Service Department 1-800-MR. COFFEE® (1-800-672-6333) or you
can visit us at www.mrcoffee.com
• Clean unit, unplug it and clean
burr mill
• Unplug unit and carefully
dislodge foreign object
• Use grind size selector to
choose the correct grind setting
• Reinsert Removable Top Burr
Grip. Twist the Removable Top
Burr Grip counterclockwise until
it stops. You should hear clicks.
Pull on the Removable Top Burr
Grip to confirm it is locked into
place.
• Set grind setting correctly
• Place Grind Chamber in proper
position
• Press and hold briefly start/stop
button again
• Plug unit in
• Wait for power to be restored
• Remove Grind Chamber, empty
and replace; unplug unit and
clean burr mill compartment if
needed
• Unplug unit for at least an hour
then plug back in and use as
needed
• Turn clockwise to set desired
number of cups
• Turn counter clockwise to set
desired number of cups
• Call Mr. Coffee® consumer
service department number
below
• Turn counterclockwise for
desired grind setting
10.
1/28/21 09:47 1/28/21 09:47